2005-2008 Yaris · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL POWER STEERING ECU

  1. C118008
    Install the power steering ECU with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C117190
    Connect the 4 connectors.

  1. C117191
    Install the wire harness clamp.

    NOTICE:
    Make sure that the wire harness of the steering post assembly is installed onto the power steering ECU bracket and that it is not pulled too tightly.


2. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.

  1. Engage the 7 clips at the rear side of the instrument panel.

    B132324

  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.

    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>

  1. B132386
    Connect the passenger airbag connector and clamp.


3. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B132321E01
  1. Engage the claws of the hinge portions by pushing the glove compartment door in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B132319E01
    Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.

  1. Install the glove compartment door stopper onto the glove compartment door.


4. INSTALL FRONT PILLAR GARNISH RH

  1. B138439E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134787
    Install the 3 clamps.

  1. Connect the antenna connector.

  1. B134781E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134779
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


5. INSTALL FRONT PILLAR GARNISH LH

  1. B138440
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B134789
    Install the 4 clamps.

  1. B134782E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip and the clip onto the front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. B134780
    w/o Curtain Shield Airbag:

    1. Engage the 2 clips and the 2 claws and install the front pillar garnish.


6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


7. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Install the front door opening trim weatherstrip.


8. INSTALL COMBINATION METER ASSEMBLY

E116835E01
  1. Install the combination meter assembly with the 2 screws.

    NOTICE:
    Install the combination meter so that the rib of the combination meter is held between the instrument panel and the instrument cluster finish panel.

  1. Connect the 2 connectors.


9. INSTALL INSTRUMENT CLUSTER FINISH PANEL

E116833
  1. Fit the 2 claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. E116834
    Engage the 5 claws and 5 clips and install the instrument cluster finish panel.


10. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end RH.


11. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.


12. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


14. CHECK SRS WARNING LIGHT
(Click here)

15. PERFORM ZERO POINT CALIBRATION
(Click here)
← REMOVAL (from Jan 2006)COMPONENTS (from Aug 2005) →