2005-2008 Yaris · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built from Jan 2006

HINT:
Use the same procedure for both the RH and LH sides.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER

B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.


3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.


4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.


5. REMOVE INSTRUMENT CLUSTER FINISH PANEL

E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.


6. REMOVE COMBINATION METER ASSEMBLY

E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.


7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.


8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.


9. REMOVE FRONT PILLAR GARNISH RH

  1. B134777E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134779
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134787
    Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.

  1. B138437E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


10. REMOVE FRONT PILLAR GARNISH LH

  1. B134778E01
    w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134780
    w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.

  1. B134789
    Using a clip remover, remove the 4 clamps.

  1. B138438E01
    w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)


11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.

  1. B132320E01
    Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.


12. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

B132322E01
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.

  1. Remove the 2 <C> bolts and 2 <B> screws.

    B132323E01

  1. Disengage the 7 clips by lifting the rear side of the instrument panel up.

    B132324

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.


13. REMOVE POWER STEERING ECU

  1. C117191
    Separate the wire harness clamp.

  1. C117190
    Disconnect the 4 connectors.

  1. C118008
    Remove the 2 bolts and remove the power steering ECU.

← COMPONENTS (from Jan 2006)INSTALLATION (from Jan 2006) →