2005-2008 Yaris · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the generator rotor assembly.

    NOTICE:
    Do not drop the generator rotor assembly.

  1. Install the generator rotor assembly and plate retainer.

  1. A033357E01
    Using a 30 mm socket wrench and press, slowly press in the rectifier end frame.

  1. A117361
    Install the 4 nuts and clip cord.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the 3 terminal insulators onto the rectifier end frame.


2. INSTALL GENERATOR HOLDER W/RECTIFIER

A117360
  1. Install the generator rectifier holder with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }


3. INSTALL GENERATOR REGULATOR ASSEMBLY

A117295
  1. Install the generator regulator assembly with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

A117359
  1. Install the plate seal.

  1. Install the generator brush holder assembly with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }

  1. Install the brush cover onto the generator brush holder assembly.

  1. Install the rear end cover with the 2 nuts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the rectifier plate with the nut and screw.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf } for nut
    3.8 N*m{ 39 kgf*cm , 34 in.*lbf } for bolt

  1. Install the terminal insulator with the nut.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }


5. INSTALL GENERATOR PULLEY

A067417E02
SST
09820-63010   (09820-06010, 09820-06020)

HINT:
SST 1-A and B
09820 - 06010
SST 2
09820 - 06020

  1. Install the generator pulley onto the generator rotor shaft by tightening the generator pulley nut by hand.

  1. Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that SST is securely fitted onto the generator rotor shaft.

  1. A033334E01
    Mount SST 2 in a vise.

  1. Insert SST 1-A and B into SST 2, and attach the generator pulley nut to SST 2.

  1. A033354E02
    Tighten the generator pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    133 N*m{ 1,356 kgf*cm , 98 ft.*lbf }

  1. Remove the generator from SST 2.

  1. A067418E02
    Turn SST 1-B, and remove SST 1-A and B.

  1. Turn the generator pulley, and check that the generator pulley moves smoothly.

← INSPECTION (from Aug 2005)INSTALLATION (from Aug 2005) →