REMOVAL
Removal / installation · Vehicles built from Aug 2005
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE COLUMN HOLE COVER SILENCER SHEET |
Remove the floor carpet and 2 clips and remove the column hole cover silencer.

| 3. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY |
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.

Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the power steering.

Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.
| 4. REMOVE FRONT WHEELS |
| 5. REMOVE ENGINE UNDER COVER LH |
| 6. REMOVE ENGINE UNDER COVER RH |
| 7. DRAIN TRANSAXLE OIL |
Remove the filler plug and gasket.
Remove the drain plug and gasket, and then drain the manual transaxle oil.
Install a new gasket and the drain plug.
- Torque:
- 39 N*m{ 400 kgf*cm , 29 ft.*lbf }
| 8. REMOVE HOOD SUB-ASSEMBLY |
| 9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.

| 10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
- HINT:
- Use the same procedure as for the LH side.
| 11. REMOVE HOOD TO COWL TOP SEAL |
![]() ![]() |
Disengage the 7 clips and remove the hood to cowl top seal.
| 12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() ![]() |
Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.
Disconnect the washer hose.

Disengage the 11 claws and clip.
Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.

| 13. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD) |
![]() ![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
| 14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() ![]() |
Disconnect the washer hose.
Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.
| 15. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD) |
![]() ![]() |
Remove the clip.
Disengage the 4 claws and remove the cowl top ventilator louver LH.
| 16. REMOVE WINDSHIELD WIPER MOTOR AND LINK |
![]() ![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 17. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO.2 |
![]() ![]() |
Disengage the claws, and remove the cowl to resister duct No. 2.
| 18. REMOVE COWL TOP PANEL OUTER |
![]() ![]() |
Disengage the clamp, and separate the wiper motor connector.
Remove the 9 bolts and the cowl top panel outer.

| 19. REMOVE BATTERY HOLD DOWN CLAMP |
| 20. REMOVE BATTERY |
| 21. REMOVE BATTERY TRAY |
| 22. REMOVE BATTERY CARRIER |
![]() ![]() |
Remove the 4 bolts and the battery carrier.
| 23. REMOVE RELEASE CYLINDER HEAT INSULATOR |
![]() ![]() |
Remove the 2 bolts and the release cylinder heat insulator.
| 24. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY |
![]() ![]() |
Remove the 4 bolts, then separate the clutch release cylinder.
- HINT:
- Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.
| 25. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() ![]() |
Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.
Remove the 2 clips and disconnect the 2 cables from the control cable bracket.
| 26. REMOVE WIRE HARNESS |
![]() ![]() |
Remove the bolt, then disconnect the wire harness.
| 27. REMOVE CONNECTOR |
Disconnect the back-up light switch connector.
| 28. REMOVE STARTER ASSEMBLY |
![]() ![]() |
Separate the harness clamp.
Remove the bolt and remove the wire harness bracket.

Remove the terminal cap.

Separate the harness clamp.
Remove the nut and disconnect terminal 30.
Disconnect the connector.
Remove the 2 bolts and remove the starter assembly.
| 29. REMOVE FRONT AXLE SHAFT LH NUT |
![]() ![]() |
Using SST and a hammer, release the staked part of the axle hub nut.
- SST
- 09930-00010
- NOTICE:
- Insert SST into the groove with the flat surface facing up.
- Do not damage the tip of SST using grinders.
- Completely unstake the staked part before removing the axle hub nut.
- Do not damage the threads of the drive shaft.
- Insert SST into the groove with the flat surface facing up.
Using a 30 mm socket wrench, remove the axle hub nut.
| 30. REMOVE FRONT AXLE SHAFT RH NUT |
- HINT:
- The removal procedure for the RH side is the same as that for the LH side.
| 31. SEPARATE SPEED SENSOR FRONT LH |
![]() ![]() |
Remove the bolt and separate the speed sensor and flexible hose.
Remove the bolt and separate the speed sensor from the steering knuckle.

- NOTICE:
- Keep the speed sensor tip and installation portion free of foreign matter.
- Remove the speed sensor without turning it from its original installation angle.
- Keep the speed sensor tip and installation portion free of foreign matter.
| 32. SEPARATE SPEED SENSOR FRONT RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 33. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH |
![]() ![]() |
Remove the clip and castle nut.
Using SST, separate the lower arm.

- SST
- 09628-00011
- NOTICE:
- Do not damage the lower ball joint dust cover.
- Suspend SST with a piece of string or the equivalent.
- Do not damage the lower ball joint dust cover.
| 34. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 35. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and castle nut.
Using SST, separate the tie rod end from the steering knuckle.

- SST
- 09628-62011
- NOTICE:
- Do not damage the tie rod end dust cover.
| 36. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 37. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() ![]() |
Remove the nut and separate the stabilizer link from the shock absorber.
- HINT:
- If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
| 38. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 39. SEPARATE FRONT AXLE ASSEMBLY LH |
Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.
- HINT:
- If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.
Push the front axle out of the vehicle to remove the drive shaft from the front axle.
- NOTICE:
- Do not push the front axle further out of the vehicle than is necessary.
- Do not damage the outboard joint boot.
- Do not damage the speed sensor rotor.
- Suspend the drive shaft with a piece of string or the equivalent.
- Do not push the front axle further out of the vehicle than is necessary.
| 40. SEPARATE FRONT AXLE ASSEMBLY RH |
- HINT:
- The separation procedure for the RH side is the same as that for the LH side.
| 41. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() ![]() |
Using SST, remove the drive shaft.
- SST
- 09520-01010
09520-24010 (09520-32040)
- NOTICE:
- Do not damage the oil seal.
- Do not damage the inboard joint boot.
- Do not drop the drive shaft.
- Do not damage the oil seal.
| 42. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() ![]() |
Using a screwdriver and hammer, remove the drive shaft.
- NOTICE:
- Do not damage the oil seal.
- Do not damage the inboard joint boot.
- Do not drop the drive shaft.
- Do not damage the oil seal.
| 43. DISCONNECT OXYGEN SENSOR CONNECTOR |
| 44. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
Remove the 4 bolts and 4 compression springs.
Remove exhaust pipe support No. 4 and the exhaust front pipe assembly.


Remove the 2 exhaust pipe gaskets.
| 45. SUSPEND ENGINE ASSEMBLY |
![]() ![]() |
Install the 2 hangers in the correct direction.
- Parts No.:
- No. 1 engine hanger 12281-40030
No. 2 engine hanger 12282-40010
Bolt 91671-80820
- Torque:
- 28 N*m{ 286 kgf*cm , 21 ft.*lbf }
Attach the engine chain hoist to the hangers.
- CAUTION:
- Do not attempt to hang the engine by hooking the chain to any other part.
| 46. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
Remove the bolt and separate the engine moving control rod.

Support the front suspension crossmember with a transmission jack.
Remove the 6 bolts and remove the suspension crossmember.

| 47. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET |
![]() ![]() |
Remove the 3 bolts and the engine moving control rod bracket.
| 48. SUPPORT MANUAL TRANSAXLE ASSEMBLY |
| 49. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR |
![]() ![]() |
Remove the bolt and nut, then separate the engine mounting insulator LH.
Remove the 4 bolts and the engine mounting insulator LH.
| 50. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET |
![]() ![]() |
Remove the 4 bolts and the engine mounting bracket LH.
| 51. REMOVE SHIFT LEVER DAMPER |
![]() ![]() |
Remove the 2 nuts and the shift lever damper.
| 52. REMOVE MANUAL TRANSAXLE ASSEMBLY |
![]() ![]() |
Remove the 9 bolts and the manual transaxle.


























