2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Air Conditioning Amplifier Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

Detection Item
Symptom
Trouble Area
Air Conditioning Amplifier Communication Stop Mode
  1. "Air Conditioner" not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "Air Conditioning Amplifier Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of air conditioning amplifier
  2. Air conditioning amplifier branch wire or connector
  3. Air conditioning amplifier

HINT:
For vehicle with air conditioning or PTC heater only.


WIRING DIAGRAM

C118189E03
C120497E12

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR DISCONNECTION (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. C131846E01
    w/ Auto air conditioning:
    1. Turn the ignition switch off.

    2. Disconnect the E11 air conditioning amplifier connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E11-11 (TX+) - E11-12 (TX-)
      Ignition Switch off
      54 to 69 Ω

  1. C131847E01
    w/ Manual air conditioning:
    1. Turn the ignition switch off.

    2. Disconnect the E8 air conditioning amplifier connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E8-2 (TX+) - E8-3 (TX-)
      Ignition Switch off
      54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)
OK


2. CHECK HARNESS AND CONNECTOR (IG+, B, GND)

  1. C131846E02
    w/ Auto air conditioning:
    1. Disconnect the E11 air conditioning amplifier connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E11-14 (GND) - Body Ground
      Always
      Below 1 Ω

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      E11-1(IG+) - Body Ground
      Ignition Switch on (IG)
      10 to 14 V
      E11- 21(B)- Body Ground
      Always
      10 to 14 V

  1. C131847E02
    w/ Manual air conditioning:
    1. Disconnect the E8 air conditioning amplifier connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      E8-12 (GND) - Body Ground
      Always
      Below 1 Ω

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      E8-8 (IG)- Body Ground
      Ignition Switch on (IG)
      10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER


← ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode (from Aug 2005)Power Steering ECU Communication Stop Mode (from Aug 2005) →