2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FENDER MARK

  1. B124292E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the fender panel.

      CAUTION:
      Do not burn yourself with the heated fender panel or infrared light.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the fender panel while it is hot from the infrared light.

      NOTICE:
      Installing the fender mark while any double-sided tape remains on the fender panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new fender mark as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    29.6 mm (1.165 in.)
    b
    17.8 mm (0.701 in.)
    c
    106.2 mm (4.181 in.)
    d
    22.9 mm (0.902 in.)
    e
    29.5 mm (1.161 in.)
    f
    18.1 mm (0.713 in.)
    g
    22.6 mm (0.890 in.)

    NOTICE:
    Install the fender mark in an environment where the ambient temperature is over 20°C (68°F). If it is less than 20°C (68°F), using an infrared light, heat the fender panel and fender mark up to 20 to 30°C (68 to 86°F) and install the fender mark.


2. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

  1. B114602E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.8 mm (6.252 in.)
    b
    40.3 mm (1.587 in.)
    c
    255.9 mm (10.075 in.)
    d
    157.6 mm (6.205 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is less than 20°C (68°F), using an infrared light, heat the luggage compartment door panel and No. 2 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.


3. INSTALL NO. 6 LUGGAGE COMPARTMENT DOOR NAME PLATE

  1. B114603E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage comparment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 6 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 6 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.5 mm (6.24 in.)
    b
    41.7 mm (1.642 in.)
    c
    266.1 mm (10.476 in.)
    d
    156.4 mm (6.157 in.)

    NOTICE:
    Install the No. 6 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is less than 20°C (68°F), using an infrared light, heat the luggage compartment door panel and No. 6 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 6 luggage compartment door name plate.


4. INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR EMBLEM

  1. B117713
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60 °C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 luggage compartment door emblem while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Insert the 2 bosses into the luggage compartment door panel and install the No. 1 luggage compartment door emblem.

    NOTICE:
    Install the No. 1 luggage compartment door emblem in an environment where the ambient temperature is over 20°C (68°F). If it is less than 20°C (68°F), using an infrared light, heat the luggage compartment door panel and No. 1 luggage compartment door emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.


5. INSTALL RADIATOR GRILLE EMBLEM

  1. B114599
    Engage the 4 claws and install the radiator grille emblem.


6. INSTALL FRONT BUMPER COVER

  1. B117704
    w/ Fog Light:

    1. Connect the 2 fog light connectors.

    2. Engage the 6 claws and install the front bumper.

  1. B117705
    w/o Fog Light:

    1. Engage the 6 claws and install the front bumper.

  1. B119955
    w/ Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 3 screws.

  1. B117706
    w/o Front Spoiler:

    1. Install the 7 clips.

    2. Install the 2 screw grommets.

    3. Tighten the 8 screws.

  1. B114359E01
    Remove the protective tape.


7. INSTALL FRONT SPOILER COVER RH (w/ Front Spoiler)

  1. B119935
    Install the front spoiler cover with the 4 screws.


8. INSTALL FRONT SPOILER COVER LH (w/ Front Spoiler)

  1. B119951
    Install the front spoiler cover with the 5 screws.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Fog Light)

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Nov 2005)COMPONENTS (from Jan 2006) →