2005-2008 Yaris · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Fog Light)

2. REMOVE FRONT SPOILER COVER LH (w/ Front Spoiler)

  1. B119950
    Remove the 5 screws and the front spoiler cover.


3. REMOVE FRONT SPOILER COVER RH (w/ Front Spoiler)

  1. B119934
    Remove the 4 screws and the front spoiler cover.


4. REMOVE FRONT BUMPER COVER

  1. B114359E01
    Apply protective tape as shown in the illustration.

  1. B119953
    w/ Front Spoiler:

    1. Remove the 3 screws.

    2. Remove the 2 screw grommets.

    3. Remove the 7 clips.

  1. B114360
    w/o Front Spoiler:

    1. Remove the 8 screws.

    2. Remove the 2 screw grommets.

    3. Remove the 7 clips.

  1. B114361E01
    w/ Fog Light:

    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper.

    2. Disconnect the 2 fog light connectors.

  1. B114365E01
    w/o Fog Light:

    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper.


5. REMOVE RADIATOR GRILLE EMBLEM

  1. B114599
    Disengage the 4 claws and remove the radiator grille emblem.


6. REMOVE NO. 1 LUGGAGE COMPARTMENT DOOR EMBLEM

  1. B117709E01
    Apply protective tape to the luggage compartment door panel in the area around the No. 1 luggage compartment door emblem.

  1. B117710E01
    Using an infrared light, heat the No. 1 luggage compartment door emblem.

    CAUTION:
    Do not burn yourself with the heated luggage compartment door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 1 luggage compartment door emblem.

  1. Remove the protective tape.


7. REMOVE NO. 6 LUGGAGE COMPARTMENT DOOR NAME PLATE

  1. B114601E01
    Apply protective tape to the luggage compartment door panel in the area around the No. 6 luggage compartment door name plate.

  1. B117711E01
    Using an infrared light, heat the No. 6 luggage compartment door name plate.

    CAUTION:
    Do not burn yourself with the heated luggage compartment door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 6 luggage compartment door name plate.

  1. Remove the protective tape.


8. REMOVE NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

  1. B114600E01
    Apply protective tape to the luggage compartment door panel in the area around the No. 2 luggage compartment door name plate.

  1. B117712E01
    Using an infrared light, heat the No. 2 luggage compartment door name plate.

    CAUTION:
    Do not burn yourself with the heated luggage compartment door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 2 luggage compartment door name plate.

  1. Remove the protective tape.


9. REMOVE FENDER MARK

B124290E01
  1. Apply protective tape to the fender panel in the area around the fender mark.

  1. Using an infrared light, heat the fender mark.

    CAUTION:
    Do not burn yourself with the heated fender panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140 °F) for 1 to 2 minutes.

  1. B124291E01
    Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the fender mark.

  1. Remove the protective tape.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →