2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL LUGGAGE COMPARTMENT DOOR NO. 2 NAME PLATE

  1. B114602E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the luggage compartment door No. 2 name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new luggage compartment door No. 2 name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.8 mm (6.252 in.)
    b
    40.3 mm (1.587 in.)
    c
    255.9 mm (10.075 in.)
    d
    157.6 mm (6.205 in.)

    NOTICE:
    Install the luggage compartment door No. 2 name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the luggage compartment door No. 2 name plate up to 20 to 30°C (68 to 86°F) and install the luggage compartment door No. 2 name plate.


2. INSTALL LUGGAGE COMPARTMENT DOOR NO. 1 NAME PLATE

  1. B114603E01
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the luggage compartment door No. 1 name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new luggage compartment door No. 1 name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.5 mm (6.24 in.)
    b
    41.7 mm (1.642 in.)
    c
    266.1 mm (10.476 in.)
    d
    156.4 mm (6.157 in.)

    NOTICE:
    Install the luggage compartment door No. 1 name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the luggage compartment door No. 1 name plate up to 20 to 30°C (68 to 86°F) and install the luggage compartment door No. 1 name plate.


3. INSTALL SYMBOL EMBLEM

  1. B117713
    Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60 °C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Insert the 2 bosses into the back door panel and install a new symbol emblem.

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.


4. INSTALL RADIATOR GRILLE NO. 2 EMBLEM

  1. B160109
    Engage the 4 claws and install the radiator grille No. 2 emblem.


5. INSTALL RADIATOR GRILLE EMBLEM

  1. B114599
    Engage the 4 claws and install the radiator grille emblem.


6. INSTALL FRONT BUMPER COVER

  1. B160100
    Connect the 2 fog light connectors.

  1. Engage the 6 claws and install the front bumper.

  1. B160161
    Install the 7 clips.

  1. B160098
    Install the 2 screw grommets.

  1. Install the 5 screws and the 3 bolts.

  1. B160160E01
    Remove the protective tape.

← REMOVAL (from Nov 2006)COMPONENTS (from Nov 2005) →