2005-2008 Yaris · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

When the ignition switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The input signal to the MREL terminal of the ECM causes a current to flow to the EFI relay coil, closing the EFI relay contacts and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A128463E01

INSPECTION PROCEDURE


1. INSPECT INTEGRATION RELAY
A107914E02
  1. Remove the integration relay from the engine room relay block.

  1. Measure the voltage between the terminal of the integration relay and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    1C-1 - Body ground
    9 to 14 V

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - BATTERY)
OK


2. INSPECT INTEGRATION RELAY (AM2 FUSE, EFI FUSE, EFI RELAY AND IG2 RELAY)
A107921E01
  1. Inspect the AM2 fuse and EFI fuse.

    1. Remove the AM2 fuse and EFI fuse.

    2. Check the fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the fuses.

  1. Inspect the relay.

    1. Check the relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1B-4
      10 kΩ or higher
      Below 1 Ω
      (When battery voltage applied to terminals 1B-2 and 1B-3)
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (When battery voltage applied to terminals 1C-1 and 1A-2)
      1C-1 - 1B-1
      Below 1 Ω



NG
REPLACE INTEGRATION RELAY
OK


3. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
A107915E07
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the A21 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    MREL (A21-44) - Integration relay (1A-2)
    Below 1 Ω
    +B (A21-2) - Integration relay (1A-4)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    MREL (A21-44) - Body ground
    10 kΩ or higher
    +B (A21-2) - Body ground

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A107892E01
  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    E1 (C20-104) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (IGSW TERMINAL VOLTAGE)
A107934E01
  1. Disconnect the A21 and C20 ECM connectors.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of ECM connectors.

    Standard voltage:
    Switch Conditions
    Specified Conditions
    IGSW (A21-28) - E1 (C20-104)
    9 to 14 V

  1. Reconnect the ECM connectors.



OK
REPLACE ECM
NG


6. INSPECT FUSE (IGN FUSE)
A107935E16
  1. Remove the IGN fuse from the main body ECU.

  1. Check the fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


7. CHECK HARNESS AND CONNECTOR (ECM - INTEGRATION RELAY)
A107915E08
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the A21 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    IGSW (A21-28) - Integration relay (1B-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    IGSW (A21-28) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed To
    Out of normal range
    A
    Within normal range (with Entry and Start System)
    B
    Within normal range (without Entry and Start System)
    C



B
Go to step 8

C
Go to step 9
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

8. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - MAIN BODY ECU)
A116136E01
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the D65 main body ECU connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) - IG2D (D65-5)
    Below 1 Ω
    Integration relay (1B-3) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    IG2D (D65-5) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

9. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - IGNITION SWITCH)
A116137E02
  1. Remove the integration relay from the engine room relay block.

  1. Disconnect the D8 ignition switch connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    Integration relay (1B-2) - IG2 (D8-6)
    Below 1 Ω
    Integration relay (1B-3) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    IG2 (D8-6) - Body ground
    10 kΩ or higher

  1. Reinstall the integration relay.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT IGNITION SWITCH ASSEMBLY
A107906E03
  1. Remove the ignition switch assembly.

  1. Check the resistance between the terminals of ignition switch assembly.

    Standard resistance:
    Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    -
    10 kΩ or higher
    ACC
    2 - 4
    Below 1 Ω
    ON
    1 - 2 - 4
    5 - 6
    START
    1 - 3 - 4
    5 - 6 - 7

  1. Reinstall the ignition switch assembly.



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)


← U0101 Lost Communication with TCM (+ U0129) (from Nov 2005)VC Output Circuit (from Nov 2005) →