Check CAN Bus Line for Short to GND (LHD Models)
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.| Symptom |
Trouble Area |
| Resistance exists between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of DLC3. |
|
- HINT:
- *1: w/ ABS
- *2: w/ VSC
- *3: w/ VSC (TMC Made)
- *4: w/ Air conditioning or PTC heater
- *5: w/ Entry and start system
- *1: w/ ABS
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
| 1. CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE) |
Turn the ignition switch off.

Disconnect the D41 D-CAN J/C connector.
Measure the resistance.

- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D15-6 (CANH) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D15-14 (CANL) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D15-6 (CANH) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D15-14 (CANL) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 2. CONNECT CONNECTOR |
Reconnect the D-CAN J/C connector.
| NEXT | |
| 3. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C SIDE) |
Turn the ignition switch off.

Disconnect the D42 P-CAN J/C connector.
Measure the resistance.

- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D15-6 (CANH) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D15-14 (CANL) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D15-6 (CANH) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D15-14 (CANL) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | |
| 4. CONNECT CONNECTOR |
Reconnect the P-CAN J/C connector.
| NEXT | |
| 5. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - ECM) |
Disconnect the D41 D-CAN J/C connector.

Measure the resistance.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 6. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU)) |
- NOTICE:
- For vehicles without ABS, go to step 7.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 7. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)) |
- NOTICE:
- For vehicles without VSC, go to step 8.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 8. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - STEERING SENSOR) |
- NOTICE:
- For vehicles without VSC, go to step 9.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-2 (STR) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-13 (STR) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-2 (STR) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-13 (STR) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 9. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - AIR CONDITIONING AMPLIFIER) |
- NOTICE:
- For vehicles without air conditioning or PTC heater, go to step 10.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 10. CHECK CAN BUS LINE FOR SHORT TO GND (D-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY) |
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-8 (A/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-19 (A/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-8 (A/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-19 (A/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | ||
| ||
| 11. CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN WIRE) |
1NZ / 2NZ / 2SZ-FE engine:

Disconnect the A21 ECM connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
1KR-FE engine:

Disconnect the A32 ECM connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
1ND-TV engine:

Disconnect the A49 ECM connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-4 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-15 (EFI) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 12. CHECK CAN BUS LINE FOR SHORT TO GND (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE) |
TMC Made:

Disconnect the A15 brake actuator (skid control ECU) connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
TMMF Made:

Disconnect the A39 brake actuator (skid control ECU) connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 13. CHECK CAN BUS LINE FOR SHORT TO GND (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE) |
TMC Made:

Disconnect the A31 ABS and traction actuator (skid control ECU) connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
TMMF Made:

Disconnect the A39 ABS and traction actuator (skid control ECU) connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-1 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-12 (ABS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 14. CHECK CAN BUS LINE FOR SHORT TO GND (STEERING SENSOR BRANCH WIRE) |
Disconnect the D62 steering sensor connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-2 (STR) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-13 (STR) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-2 (STR) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-13 (STR) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 15. CHECK CAN BUS LINE FOR SHORT TO GND (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
w/ Auto air conditioning:

Disconnect the E11 air conditioning amplifier connector
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
w/ Manual air conditioning:

Disconnect the E8 air conditioning amplifier connector
Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-6 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-17 (A/C) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 16. CHECK CAN BUS LINE FOR SHORT TO GND (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
Disconnect the D16 center airbag sensor assembly connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D41 D-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D41-8 (A/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-19 (A/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-8 (A/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-19 (A/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 17. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - POWER STEERING ECU) |
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-4 (EPS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-15 (EPS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-4 (EPS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D42-15 (EPS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 18. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - MAIN BODY ECU) |
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 19. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - YAW RATE SENSOR) |
- NOTICE:
- For vehicles without VSC (TMC made), go to step 20.
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-2 (YAW) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-13 (YAW) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-2 (YAW) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-13 (YAW) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 20. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - CERTIFICATION ECU) |
- NOTICE:
- For vehicles without entry and start system, go to step 21.
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-6 (SMRT) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-18 (SMRT) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-6 (SMRT) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-18 (SMRT) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | |
| 21. CHECK CAN BUS LINE FOR SHORT TO GND (P-CAN J/C - COMBINATION METER ECU) |
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-7 (MET) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-18 (MET) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-7 (MET) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-18 (MET) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| OK | ||
| ||
| 22. CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU) |
Disconnect the D31 power steering ECU connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-4 (EPS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-15 (EPS) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-4 (EPS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D42-15 (EPS) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 23. CHECK CAN BUS LINE FOR SHORT TO GND (MAIN BODY ECU BRANCH WIRE) |
w/ Entry and start system:

Disconnect the D66 main body ECU connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
w/o Entry and start system:

Disconnect the D33 main body ECU connector.
Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-5 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-16 (J/B) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 24. CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR BRANCH WIRE) |
Disconnect the D63 yaw rate sensor connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-2 (YAW) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-13 (YAW) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-2 (YAW) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-13 (YAW) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 25. CHECK CAN BUS LINE FOR SHORT TO GND (CERTIFICATION ECU BRANCH WIRE) |
Disconnect the D60 certification ECU connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-6 (SMRT) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-18 (SMRT) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-6 (SMRT) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-18 (SMRT) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
| 26. CHECK CAN BUS LINE FOR SHORT TO GND (COMBINATION METER ECU BRANCH WIRE) |
Disconnect the D1 combination meter ECU connector.

Measure the resistance.

- HINT:
- The resistance must be measured after the D42 P-CAN J/C connector is disconnected.
- Result:
Tester Connection
Condition
Specified Condition
Proceed to
D42-7 (MET) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D41-18 (MET) - D15-4 (CG)
Ignition switch off
1 Ω or higher
OK
D42-7 (MET) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
D41-18 (MET) - D15-4 (CG)
Ignition switch off
Below 1 Ω
NG
|
|
||||
| NG | ||
| ||
