2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to +B (RHD Models)

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

There may be a short circuit between the CAN bus line and +B when no resistance exits between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.
Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering sensor*2
  6. Yaw rate sensor*3
  7. ECM
  8. Center airbag sensor assembly
  9. Air conditioning amplifier*4
  10. Combination meter ECU
  11. Main body ECU
  12. Certification ECU*5

HINT:
  1. *1: w/ ABS
  2. *2: w/ VSC
  3. *3: w/ VSC (TMC Made)
  4. *4: w/ Air conditioning or PTC heater
  5. *5: w/ Entry and start system


WIRING DIAGRAM

C132284E01
C132285E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE)

  1. G100291E28
    Turn the ignition switch off.

  1. Disconnect the D42 D-CAN J/C connector.

  1. C118856E32
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2. CONNECT CONNECTOR
  1. Reconnect the D-CAN J/C connector.


NEXT


3. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C SIDE)

  1. G100291E29
    Turn the ignition switch off.

  1. Disconnect the D41 P-CAN J/C connector.

  1. C118856E32
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
Go to step 17
NG


4. CONNECT CONNECTOR
  1. Reconnect the D41 P-CAN J/C connector.


NEXT


5. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - POWER STEERING ECU)

  1. C133293E21
    Disconnect the D42 D-CAN J/C connector.

  1. Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 11
OK


6. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - STEERING SENSOR)

NOTICE:
For vehicles without VSC, go to step 7.

  1. C133293E22
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 12
OK


7. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - YAW RATE SENSOR)

NOTICE:
For vehicles without VSC (TMC made), go to step 8.

  1. C133293E23
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 13
OK


8. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - MAIN BODY ECU)

  1. C133293E24
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-5 (J/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-16 (J/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-5 (J/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-16 (J/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 14
OK


9. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - CERTIFICATION ECU)

NOTICE:
For vehicles without entry and start system, go to step 10.

  1. C133293E25
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-6 (SMRT) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-17 (SMRT) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-6 (SMRT) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-17 (SMRT) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 15
OK


10. CHECK CAN BUS LINE FOR SHORT TO +B (D-CAN J/C - COMBINATION METER ECU)

  1. C133293E26
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 16
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))

11. CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU MAIN WIRE)

  1. G100242E28
    Disconnect the D31 power steering ECU connector.

  1. C133293E21
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-4 (EPS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-15 (EPS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE POWER STEERING ECU
NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L)

12. CHECK CAN BUS LINE FOR SHORT TO +B (STEERING SENSOR BRANCH WIRE)

  1. G030155E31
    Disconnect the D62 steering sensor connector.

  1. C133293E22
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-1 (STR) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-12 (STR) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE STEERING SENSOR
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING SENSOR (CAN-H, CAN-L)

13. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR BRANCH WIRE)

  1. C125957E04
    Disconnect the D63 yaw rate sensor connector.

  1. C133293E23
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-2 (YAW) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-13 (YAW) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)

14. CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU BRANCH WIRE)

  1. C131839E02
    w/ Entry and start system:
    1. Disconnect the D66 main body ECU connector.

    2. C133293E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D42-5 (J/B) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D42-16 (J/B) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D42-5 (J/B) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D42-16 (J/B) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C131840E02
    w/o Entry and start system:
    1. Disconnect the D33 main body ECU connector.

    2. C133293E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D42-5 (J/B) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D42-16 (J/B) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D42-5 (J/B) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D42-16 (J/B) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE MAIN BODY ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)

15. CHECK CAN BUS LINE FOR SHORT TO +B (CERTIFICATION ECU BRANCH WIRE)

  1. G100280E10
    Disconnect the D60 main body ECU connector.

  1. C133293E25
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-6 (SMRT) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-17 (SMRT) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-6 (SMRT) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-17 (SMRT) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE CERTIFICATION ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CAN-H, CAN-L)

16. CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU BRANCH WIRE)

  1. C139156E04
    Disconnect the D1 combination meter ECU connector.

  1. C133293E26
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-7 (MET) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D42-18 (MET) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE COMBINATION METER ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER ECU (CAN-H, CAN-L)

17. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - ECM)

  1. C133293E27
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-4 (EFI) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-15 (EFI) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-4 (EFI) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-15 (EFI) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 22
OK


18. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without ABS, go to step 19.

  1. C133293E28
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 23
OK


19. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - ABS AND TRACTION ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without VSC, go to step 20.

  1. C133293E28
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-1 (ABS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-12 (ABS) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 24
OK


20. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - AIR CONDITIONING AMPLIFIER)

NOTICE:
For vehicles without air conditioning or PTC heater, go to step 21.

  1. C133293E29
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-6 (A/C) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-17 (A/C) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-6 (A/C) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-17 (A/C) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 25
OK


21. CHECK CAN BUS LINE FOR SHORT TO +B (P-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C133293E30
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 26
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (P-CAN J/C - D-CAN J/C (CAN-H, CAN-L))

22. CHECK CAN BUS LINE FOR SHORT TO +B (ECM MAIN WIRE)

  1. C125895E08
    1NZ / 2NZ / 2SZ-FE engine:
    1. Disconnect the A21 ECM connector.

    2. C133293E27
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C118186E05
    1KR-FE engine:
    1. Disconnect the A32 ECM connector.

    2. C133293E27
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130899E05
    1ND-TV engine:
    1. Disconnect the A49 ECM connector.

    2. C133293E27
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-15 (EFI) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)

23. CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

  1. C118165E05
    TMC Made:
    1. Disconnect the A15 brake actuator (skid control ECU) connector.

    2. C133293E28
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130880E10
    TMMF Made:
    1. Disconnect the A39 brake actuator (skid control ECU) connector.

    2. C133293E28
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)

24. CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

  1. C118187E04
    TMC Made:
    1. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

    2. C133293E28
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130880E08
    TMMF Made:
    1. Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

    2. C133293E28
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-12 (ABS) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)

25. CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. C131846E04
    w/ Auto air conditioning:
    1. Disconnect the E11 air conditioning amplifier connector.

    2. C133293E29
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-6 (A/C) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-17 (A/C) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-6 (A/C) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-17 (A/C) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG

  1. C131847E04
    w/ Manual air conditioning:
    1. Disconnect the E8 air conditioning amplifier connector.

    2. C133293E29
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-6 (A/C) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-17 (A/C) - D15-16 (BAT)
      Ignition switch off
      1 Ω or higher
      OK
      D41-6 (A/C) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG
      D41-17 (A/C) - D15-16 (BAT)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE AIR CONDITIONING AMPLIFIER
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)

26. CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

  1. C131069E01
    Disconnect the D16 center airbag sensor assembly connector.

  1. C133293E30
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D41-8 (A/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D41-19 (A/B) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)


← Check CAN Bus Line for Short to GND (LHD Models) (from Aug 2005)Check CAN Bus Line for Short to GND (RHD Models) (from Aug 2005) →