2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. BEARING POSITION

C080723

2. ADJUST TAPERED ROLLER BEARING PRELOAD
  1. Coat the front differential case and bearing with ATF, and install them onto the transaxle case.

    NOTICE:
    Do not install the drive pinion.

  1. C080710
    Install the transaxle housing onto the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. D025185E01
    Using SST and a small torque wrench, measure the preload of the differential gear.
    SST
    09564-32011  

    Preload:
    Bearing
    Standard
    New
    0.78 to 1.37 N*m (8.0 to 14.0 kgf*cm, 6.9 to 12.2 in.*lbf)
    Used
    0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)

    If the preload is not within the specifications, remove the differential from the transaxle case.
    Select a new transaxle case side adjusting shim in accordance with the following table.

    Adjusting shim thickness:
    mm (in.):
    Mark
    Thickness
    mm (in.)
    Mark
    Thickness
    mm (in.)
    A
    1.80 (0.0709)
    N
    2.26 (0.0890)
    B
    1.85 (0.0728)
    P
    2.29 (0.0902)
    C
    1.90 (0.0748)
    Q
    2.32 (0.0913)
    D
    1.95 (0.768)
    R
    2.35 (0.0925)
    E
    2.00 (0.0787)
    S
    2.40 (0.0945)
    F
    2.05 (0.0807)
    T
    2.45 (0.0965)
    G
    2.08 (0.0819)
    U
    2.50 (0.0984)
    H
    2.11 (0.0831)
    V
    2.55 (0.1004)
    J
    2.14 (0.0843)
    W
    2.60 (0.1024)
    K
    2.17 (0.0854)
    X
    2.65 (0.1043)
    L
    2.20 (0.0866)
    Y
    2.70 (0.1063)
    M
    2.23 (0.0878)



3. INSTALL BREATHER PLUG NO. 1

C123279
  1. Coat a new O-ring with ATF, and install it onto breather plug No. 1.

  1. Install breather plug No. 1 onto the transaxle case.


4. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

C059795
  1. Install the differential gear lube apply tube onto the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.


5. INSTALL TRANSMISSION LUBE APPLY TUBE

C059794
  1. Install the transmission lube apply tube onto the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.


6. INSTALL TRANSAXLE APPLY TUBE CLAMP NO. 1

C059824
  1. Install transaxle apply tube clamp No. 1 onto the transaxle housing with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


7. INSTALL TRANSAXLE HOUSING OIL SEPARATOR

C059793
  1. Install the transaxle housing oil separator onto the transaxle housing with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


8. INSTALL TRANSMISSION CASE PLATE NO. 1

C059802
  1. Install transmission case plate No. 1 onto the transaxle case with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


9. INSTALL TRANSAXLE CASE NO. 1 PLUG

C059902
  1. Coat 2 new O-rings with ATF, and install them onto the 2 transaxle case No. 1 plugs.

  1. Install the 2 transaxle case No. 1 plugs onto the transaxle housing.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


10. INSTALL TRANSAXLE HOUSING NO. 2 PLUG

C059823
  1. Coat a new O-ring with ATF, and install it onto the transaxle housing No. 2 plug.

  1. Install the transaxle housing No. 2 plug to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


11. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

D025186E01
  1. Coat a new oil seal with ATF.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal onto the transaxle case.

    SST
    09950-60010   (09951-00210)
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    0.75 to 1.25 mm (0.030 to 0.049 in.)


12. INSTALL PARKING LOCK PAWL

C059865
  1. Coat the parking lock pawl shaft with ATF.

  1. Install the parking lock pawl shaft, torsion spring and parking lock pawl onto the transaxle case.

    NOTICE:
    Check that the edge of the torsion spring fits into the groove securely.


13. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

C059863
  1. Install the manual detent spring with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


14. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

C060849
  1. Install the parking lock rod onto the manual valve lever.


15. INSTALL MANUAL VALVE LEVER SHAFT

C059855E01
  1. Coat the manual valve lever with ATF.

  1. Install a new spacer onto the manual valve lever.

  1. Install the manual valve lever shaft and manual valve lever.

    NOTICE:
    Do not damage the oil seal when installing the manual valve lever shaft.

  1. Using a pin punch and hammer, drive in the spring pin.

  1. Turn the spacer and lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.
    Using a pin punch, stake the spacer through the small hole.
    Check that the spacer does not turn.


16. INSTALL PARKING LOCK PAWL BRACKET

C059860
  1. Install the parking lock pawl bracket with the 2 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


17. INSTALL 1ST AND REVERSE BRAKE O-RING

C080716
  1. Coat 2 new O-rings with ATF, and install them onto the 1st and reverse brake piston.


18. INSTALL 1ST AND REVERSE BRAKE PISTON

C059900
  1. Coat the 1st and reverse brake piston with ATF, and install it onto the transaxle case.

    NOTICE:
    Do not damage the O-ring of the 1st and reverse brake piston.


19. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C059856
  1. Coat the 1st and reverse brake return spring with ATF, and install it onto the transaxle case.


20. INSTALL 1ST AND REVERSE BRAKE DISC

C082195E01
  1. Coat the 4 plates, 4 discs and flange with ATF, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.

  1. C060825E01
    Using SST, a press and a screwdriver, install the snap ring.
    SST
    09387-00100  
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the snap ring is installed in the groove of the transaxle case correctly.


21. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

D025187E01
  1. Using a dial indicator and measuring terminal (SST), measure the 1st and reverse brake piston stroke while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

    SST
    09350-36010   (09350-06110)

    Piston stroke:
    0.791 to 1.489 mm (0.031 to 0.057 in.)

    If the piston stroke is outside the specifications, inspect the discs, plates and flange.


22. INSTALL COUNTER DRIVE GEAR

C080718E01
  1. Using SST and a press, install the counter drive gear.

    SST
    09223-15030  
    09387-00060  
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

    NOTICE:
    Do not apply excessive force to the transaxle case.


23. INSTALL PLANETARY RING GEAR

C059866
  1. Install the planetary ring gear onto the new planetary ring gear flange and fix the snap ring using a screwdriver.


24. INSTALL PLANETARY RING GEAR FLANGE

C080719E01
  1. Using SST and a press, install the planetary ring gear.

    SST
    09223-15030  
    09387-00060  
    09950-60010   (09951-00500)
    09950-70010   (09951-07100)


25. INSTALL COUNTER DRIVE GEAR NUT
  1. Using a 55 mm socket wrench, install a new counter drive gear nut onto the planetary gear flange.

    HINT:
    Torque : 100 N*m (1,020 kgf*cm, 74 ft.*lbf)

  1. C060714
    Inspect the preload of the counter drive gear bearing.

    Preload:
    0.05 to 0.35 N*m (0.5 to 3.6 kgf*cm, 0.43 to 3.12 in.*lbf)

    HINT:
    Tighten the counter drive gear nut gradually so that the preload is within the specifications.

  1. C080715E01
    Using SST, lift the transaxle case.
    SST
    09213-14010  
    09387-00060  

  1. C060715
    Using a chisel and a hammer, stake the counter drive gear nut.


26. INSTALL PLANETARY GEAR ASSEMBLY

C059857
  1. Coat the planetary gear with ATF, and install it onto the transaxle housing.


27. INSTALL 1 WAY CLUTCH NO. 2

C059854
  1. Coat 1-way clutch No. 2 with ATF, and install it onto the transaxle.


28. INSPECT 1 WAY CLUTCH NO. 2

D025182E01
  1. Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.


29. INSTALL OUTER RACE RETAINER

C059853
  1. Install the anti-rattle clip in the place shown in the illustration (the space between the No. 2 1-way clutch outer race and transaxle case). Push the anti-rattle clip in until it makes a click sound.


30. INSTALL BRAKE DRUM GASKET

C059852
  1. Coat a new brake drum gasket with ATF, and install it onto the transaxle case.


31. INSTALL 2ND BRAKE BRAKE DISC

D025188E01
  1. Coat the flange, 2 discs and 2 plates with ATF, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


32. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C059850
  1. Coat the 2nd brake piston return spring with ATF, and install it onto the transaxle case.


33. INSTALL 2ND BRAKE PISTON ASSEMBLY

C060853
  1. Coat the 2nd brake piston with ATF, and install it as shown in the illustration.

  1. C059837E01
    Using SST, a press and a screwdriver, remove the snap ring.
    SST
    09387-00100  
    09950-70010   (09951-07100)


34. INSTALL FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE

C060847
  1. Coat the thrust bearing race with ATF, and install it onto the front planetary sun gear.


35. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

C060845
  1. Coat the planetary sun gear with ATF, and install it onto the transaxle.


36. INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

C059895
  1. Using a screwdriver, install the snap ring onto the transaxle case.


37. INSTALL PLANETARY CARRIER THRUST WASHER

C059890
  1. Coat the planetary carrier thrust washer with petroleum jelly, and install it onto the planetary gear.


38. INSTALL 1 WAY CLUTCH ASSEMBLY

C059835
  1. Coat planetary carrier thrust washer No. 2 with petroleum jelly.

  1. Install planetary carrier thrust washer No. 2 and the 1-way clutch onto the planetary sun gear.


39. INSPECT 1 WAY CLUTCH ASSEMBLY

D025181E02
  1. Hold the rear planetary sun gear and turn the 1 way clutch.

  1. Make sure that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.


40. INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

C059836
  1. Coat the needle roller bearing with ATF, and install it onto the rear planetary gear.


41. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

C059834
  1. Coat the rear planetary sun gear with ATF, and install it onto the transaxle case.


42. INSTALL FORWARD CLUTCH HOB THRUST BEARING RACE

C059889
  1. Coat the thrust bearing race with ATF, and install it onto the transaxle case.


43. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

C059833
  1. Coat the thrust needle roller bearing with ATF, and install it onto the forward clutch hub.


44. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

C059831
  1. Coat the forward clutch hub with ATF, and install it onto the transaxle case.


45. INSTALL SUN GEAR REAR THRUST BEARING

C059832
  1. Coat the thrust bearing and 2 bearing races with ATF, and install them onto the intermediate shaft.


46. INSTALL INTERMEDIATE SHAFT ASSEMBLY

C059830
  1. Coat the intermediate shaft with ATF, and install it onto the transaxle case.


47. INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC

D025189E01
  1. Coat the plate, 2 discs and 2 flanges with ATF, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


48. INSPECT 2ND COAST AND OVER DRIVE BRAKE FLANGE, DISK AND PLATE

C059893E01
  1. Using a straight edge and vernier calipers, measure dimension A from the transaxle case end surface to the brake flange.

  1. C059894E01
    Using a straight edge and vernier calipers, measure dimension B from the piston to the edge surface of the transaxle rear cover assembly.

  1. Calcurate the clearance from the measured dimensions A and B.

    Piston clearance:
    0.65 to 1.05 mm (0.0256 to 0.0413 in.)

    HINT:
    1. Piston clearance = Dimension A - Dimension B.
    2. If the result is not as specified, select a new brake flange.

    Flange thickness:
    Mark
    Thickness
    mm (in.)
    Piston stroke value
    mm (in.)
    0
    3.0
    (0.118)
    0.738 to 0.949
    (0.02905 to 0.03736)
    1
    3.2
    (0.126)
    0.950 to 1.149
    (0.03740 to 0.04524)
    2
    3.4
    (0.134)
    1.150 to 1.349
    (0.04528 to 0.05311)
    3
    3.6
    (0.142)
    1.350 to 1.549
    (0.05315 to 0.06098)
    0
    3.8
    (0.150)
    1.550 to 1.702
    (0.06102 to 0.06701)


49. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

C059827
  1. Coat 4 new apply gaskets with ATF, and install them onto the transaxle rear cover.


50. INSTALL FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

C059826
  1. Coat the thrust needle roller bearing with ATF, and install it onto the forward and reverse clutch.


51. INSTALL TRANSAXLE REAR COVER ASSEMBLY

C059899
  1. Apply FIPG to the transaxle rear cover.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

  1. C059804
    Install the transaxle rear cover onto the transaxle case with the 9 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


52. INSTALL GOVERNOR APPLY GASKET NO. 2

C059803
  1. Coat a new governor apply gasket No. 2 with ATF, and install it onto the transaxle case.


53. INSTALL DIFFERENTIAL GEAR ASSEMBLY

C059801
  1. Coat the differential gear and drive pinion with ATF, and install them onto the transaxle case.


54. INSTALL DIRECT CLUTCH HUB

C059825
  1. Coat the direct clutch hub with ATF, and install it onto the transaxle case.


55. INSTALL PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING

C060793
  1. Coat the thrust bearing race and thrust needle roller bearing with ATF, and install them onto the transaxle case.


56. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING

C059849
  1. Coat the thrust needle roller bearing with ATF, and install it onto the transaxle case.

    NOTICE:
    Check the direction of the bearing.


57. INSTALL INPUT SHAFT ASSEMBLY

C059800
  1. Coat the input shaft with ATF, and install it onto the transaxle case.


58. INSTALL OIL PUMP ASSEMBLY

C080728
  1. Place the oil pump through the input shaft, and align the bolt holes in the oil pump with those in the transaxle case.

  1. Install the 6 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


59. INSPECT INPUT SHAFT ASSEMBLY

C080729
  1. Make sure that the input shaft turns smoothly.


60. INSPECT INPUT SHAFT END PLAY

C080727
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.3 to 0.9 mm (0.012 to 0.035 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.


61. INSTALL TRANSAXLE HOUSING

C059886
  1. Apply FIPG to the transaxle housing.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent

  1. C080710E01
    Install the transaxle housing onto the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    Apply seal packing or the equivalent to the 4 bolts indicated by arrows.

    Seal packing:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent


62. INSTALL B-1 ACCUMULATOR PISTON COMPRESSION SPRING

C060004
  1. Install the B-1 accumulator piston compression spring onto the piston B-1 accumulator.


63. INSTALL PISTON B-1 ACCUMULATOR

D025193
  1. Coat 2 new O-rings with ATF, and install them onto the B-1 accumulator piston.

  1. C060822
    Coat the B-1 accumulator piston with ATF, and install it onto the transaxle case.


64. INSTALL C-1 ACCUMULATOR SPRING SUB-ASSEMBLY

C059790
  1. Install the C-1 accumulator spring into the C-1 accumulator piston.


65. INSTALL C-1 ACCUMULATOR PISTON

D025194
  1. Coat 2 new O-rings with ATF and install them onto the C-1 accumulator piston.

  1. C060823
    Coat the C-1 accumulator piston with ATF, and install it onto the transaxle case.


66. INSTALL C-2 ACCUMULATOR SPRING SUB-ASSEMBLY

C059787
  1. Install the C-2 accumulator spring onto the C-2 accumulator piston with the snap ring.


67. INSTALL C-2 ACCUMULATOR PISTON

D025195
  1. Coat 2 new O-rings with ATF, and install them onto the C-2 accumulator piston.

  1. C060824
    Coat the C-2 accumulator piston with ATF, and install it onto the transaxle case.


68. INSTALL CHECK BALL BODY

C059785
  1. Coat the spring and the check ball body with ATF, and install them onto the transaxle case.


69. INSTALL GOVERNOR APPLY GASKET NO. 1

C059784
  1. Coat new governor apply gasket No. 1 with ATF, and install it onto the transaxle case.


70. INSTALL TRANSMISSION WIRE

D025196
  1. Coat a new O-ring with ATF, and install it onto the transmission wire.

  1. Insert the transmission wire into the transaxle.

  1. C057520
    Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


71. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

C057516E02
  1. Connect the connecting rod to the manual valve lever, and install the transmission valve body.

  1. D025197E01
    Install the 14 bolts into the positions shown in the illustration and tighten them uniformly.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    When installing the valve body onto the transaxle case, do not hold the solenoids.

    Bolt length:
    Bolt A:
    20 mm (0.79 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    49 mm (1.93 in.)
    Bolt D:
    36 mm (1.42 in.)
    Bolt E :
    40 mm (1.57 in.)

  1. D025198E01
    Install the oil temperature sensor and connect the solenoid connectors.


72. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C057509
  1. Install a new gasket onto the oil strainer.

  1. C057507
    Install the oil strainer onto the transaxle assembly with 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


73. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

C057519E01
  1. Install the 2 oil cleaner magnets onto the 2 positions shown in the illustration.

  1. C057506
    Install a new oil pan gasket and oil pan onto the transaxle assembly with 18 bolts.

    Torque:
    7.0 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Install a new drain plug gasket and drain plug to the oil pan.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


74. INSTALL TRANSAXLE HOUSING OIL SEAL

D025191E01
  1. Using SST and a hammer, drive in a new oil seal.

    Oil seal drive in depth:
    3.1 mm (0.122 in.)

    SST
    09517-12010  
    09630-24014   (09620-24051)

  1. Apply MP grease to the lip of the transaxle housing oil seal.


75. INSTALL TRANSAXLE CASE OIL SEAL

D025192E01
  1. Using SST and a hammer, drive in a new oil seal.

    SST
    09316-60011   (09316-00011)

    Oil seal drive in depth:
    3.1 mm (0.122 in.)

  1. Apply MP grease to the lip of the transaxle oil seal.


76. INSTALL OIL COOLER TUBE UNION

C059821
  1. Coat 2 new O-rings with ATF, and install them onto the 2 oil cooler tube unions.

  1. Install the 2 oil cooler tube unions onto the transaxle assembly.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


77. INSTALL BREATHER PLUG HOSE

C059820
  1. Install the breather plug hose onto the breather plug with the clamp.


78. INSTALL TRANSMISSION REVOLUTION SENSOR

C059782
  1. Coat a new O-ring with ATF, and install it onto the transmission revolution sensor.

  1. Install the transmission revolution sensor onto the transaxle assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


79. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C057491
  1. Provisionally fasten the neutral start switch with the 2 bolts.

  1. C057492
    Install the nut stopper and nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Provisionally install the control shaft lever.

  1. C057493
    Turn the control shaft lever counterclockwise until it stops, then turn it clockwise 2 notches.

  1. D025199
    Align the groove with the neutral basic line, and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C057495
    Using a screwdriver, stake the nut with the lock washer.


80. INSTALL TRANSMISSION CONTROL SHAFT LEVER

C057496
  1. Install the control lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Aug 2005)COMPONENTS (from Aug 2005) →