REASSEMBLY
Removal / installation · Vehicles built from Aug 2005
| 1. INSTALL FRONT DIFFERENTIAL SIDE GEAR |
![]() ![]() |
Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF, and install them onto the differential case.
| 2. INSTALL FRONT DIFFERENTIAL PINION SHAFT NO. 1 |
![]() ![]() |
Coat front differential pinion shaft No. 1 with ATF, and install it onto the differential case.
| 3. INSPECT BACKLASH |
![]() ![]() |
Using a dial indicator, inspect the backlash of the side gear.
- Standard backlash:
- 0.05 to 0.20 mm (0.0020 to 0.0079 in.)
- Thrust washer thickness:
Mark
Thickness
-
1.50 mm (0.0589 in.)
-
1.55 mm (0.0609 in.)
-
1.60 mm (0.0629 in.)
-
1.65 mm (0.0649 in.)
-
1.70 mm (0.0669 in.)
-
1.75 mm (0.0689 in.)
| 4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() ![]() |
Using a 3 mm pin punch and hammer, install the pinion shaft straight pin.
Using a chisel and hammer, stake the differential case.

| 5. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() ![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).
Clean the contact surface of the front differential case.
Aligh the matchmarks on the front differential ring gear and the differential case, and install the front differential ring gear case while it is still hot.

Tighten the 8 bolts.

- Torque:
- 78 N*m{ 790 kgf*cm , 57 ft.*lbf }
| 6. INSTALL SPEEDOMETER DRIVE GEAR |
![]() ![]() |
Install the speedometer drive gear onto the differential case.
| 7. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a press, install the front differential case front tapered roller bearing (inner race) onto the differential case.
- SST
- 09608-06041
Using SST and a hammer, install the front differential case front tapered roller bearing (outer race) onto the transaxle housing.

- SST
- 09950-60020
(09951-00680)
09950-70010 (09951-07100)
09950-60010 (09951-00340)
| 8. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a press, install the front differential case rear tapered roller bearing (inner race) onto the differential case.
- SST
- 09608-06041
Using SST and a hammer, install the case washer and front differential case rear tapered roller bearing (outer race) onto the transaxle case.

- SST
- 09950-60020
(09951-00710)
09950-70010 (09951-07100)
| 9. INSTALL DIFFERENTIAL DRIVE PINION PLUG |
![]() ![]() |
Using a 10 mm socket wrench and hammer, install a new differential drive pinion plug onto the differential drive pinion.
- Standard clearance:
- 2.3 to 2.35 mm (0.090 to 0.093 in.)
| 10. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a press, install the front drive pinion front tapered roller bearing (inner race) onto the differential drive pinion.
Using SST and a hammer, install the front drive pinion front tapered roller bearing (outer race) onto the transaxle housing.

- SST
- 09608-04031
09950-60010 (09951-00540)
09950-70010 (09951-07100)
| 11. INSTALL COUNTER DRIVE GEAR |
![]() ![]() |
Using SST and a press, install the counter drive gear onto the differential drive pinion.
- SST
- 09608-04031
09950-60010 (09951-00280)
| 12. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() ![]() |
Using SST and a press, install the front drive pinion rear tapered roller bearing (inner race) onto the differential drive pinion.
Using SST and a hammer, install the pinion washer and front drive pinion rear tapered roller bearing (outer race) onto the transaxle case.

- SST
- 09608-04031
09950-60010 (09951-00280, 09951-00600)
09950-70010 (09951-07100)












