2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (w/ Front Seat Side Airbag) (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when installing the front seat.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.


1. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B114767E01
    for Driver Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.

    3. B127001
      Install the 4 clamps.

    4. Install the buckle switch connector.

    5. w/ Seat Heater System:

      1. Connect the seat heater connector.

    6. Engage the 2 hooks and install the front seat cushion cover.

  1. B114763E01
    for Front Passenger Side:

    1. Install the front seat inner belt with the bolt.

      Torque:
      42 N*m{ 430 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt over the convex areas of the front seat frame adjuster.

    2. Install the wire harness into the claw of the front seat cushion shield.

    3. B127000
      Install the 5 clamps.

    4. Install the buckle switch connector.

    5. Connect the occupant detection sensor connector.

    6. w/ Seat Heater System:

      1. Connect the seat heater connector.

    7. Engage the 2 hooks and install the front seat cushion cover.


2. INSTALL FRONT SEAT ASSEMBLY

B119882E01

NOTICE:
Follow the procedure described below in order to prevent the seat tracks from locking separately.

  1. Insert the 2 location pins through the 2 body holes, place the front seat in the most forward position and make sure that the inner and outer seat tracks are locked securely.

  1. Using "Torx" socket wrench E10, install bolt 1 and then bolt 2 onto the rear side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are securely locked.

  1. Using "Torx" socket wrench E10, install bolt 3 and then bolt 4 onto the rear side.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.

    HINT:
    If the inner and outer seat tracks do not lock simultaneously, loosen the bolts and adjust the seat tracks.

  1. B119883
    w/ Front Seat Side Airbag:

    1. Connect the airbag connector.

  1. Connect the buckle switch connector.


3. INSTALL FRONT SEAT UNDER TRAY (w/ Under Tray)

  1. B119884
    Hitch the front seat under tray firmly onto the seat track, and then slide it along the seat track to install it.


4. INSTALL FRONT SEAT HEADREST ASSEMBLY

  1. B138677E01
    Push in the 2 lock buttons of the front seat headrest supports and install the 2 front seat headrests.


5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


6. INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)
(Click here)
← INSPECTION (from Aug 2005)COMPONENTS (from Nov 2005) →