B1423/23 Pressure Sensor Circuit
Diagnostic trouble codes · Vehicles built from Aug 2005
DESCRIPTION
This DTC is output when the refrigerant pressure is either extremely low (0.19 Mpa [2.0 kgf/cm2 , 28psi] or less) or extremely high (3.14 Mpa [32.0 kgf/cm2, 455 psi] or more). The air conditioning pressure sensor, which is installed on the pipe of the high pressure side, detects the refrigerant pressure and sends a refrigerant pressure signals to the air conditioning amplifier. The air conditioning amplifier determines the pressure from the signals in accordance with the sensor characteristics, and controls the compressor accordingly.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1423/23 |
Open or short in air conditioning pressure sensor circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK REFRIGERANT |
![]() ![]() |
Check the sight glass of the cooler unit refrigerant liquid pipe.
Prepare the vehicle in accordance with the chart below.
Item
Condition
Engine Speed
1500 rpm
Vehicle Doors
Fully open
Temperature Setting
MAX COLD
Blower Speed
HI
A/C switch
ON
Compare the sight glass to the following chart.
Item
Symptom
Amount of Refrigerant
Corrective Procedures
1
Bubbles visible
Insufficient*
- Check for gas leakage and repair if necessary
- Add refrigerant until bubbles disappear
2
No bubbles visible
Empty, insufficient or too much
Refer to items 3 and 4
3
No temperature difference between compressor inlet and outlet
Empty or nearly empty
- Check for gas leakage with gas leak detector and repair if necessary
- Add refrigerant until bubbles disappear
4
Considerable temperature difference between compressor inlet and outlet
Correct or too much
Refer to items 5 and 6
5
Refrigerant becomes clear immediately after A/C turned OFF
Too much
- Drain or discharge refrigerant
- Bleed air and supply proper amount of purified refrigerant
6
Refrigerant foams and then becomes clear immediately after A/C turned OFF
Correct
-
- HINT:
- *: If the ambient temperature is higher than usual but cooling is sufficient, bubbles in the sight glass are permissible.
- Check for gas leakage and repair if necessary
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (REG PRESS SENS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch ON.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
- Data List / Air Conditioner:
Item
Measure Item / Display
(Range)
Normal Condition
Diagnostic Note
Reg Press Sens
Regulator Pressure Sensor /
Min.: 0, Max.: 255
Actual regulator pressure is displayed
-
- OK:
- The display is as specified in the normal condition column.
- Result:
Result
Proceed to
NG
A
OK (Checking from the PROBLEM SYMPTOMS TABLE)
B
OK (Checking from the DTC)
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER) |
![]() ![]() |
Disconnect the A3 air conditioning pressure sensor connector.
Disconnect the E11 air conditioning amplifier connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
A3-3 (+) - E11-10 (S5-3)
Below 1 Ω
A3-2 (PR) - E11-9 (PRE)
Below 1 Ω
A3-1 (-) - E11-13 (SG-2)
Below 1 Ω
A3-3 (+) - Body ground
1MΩ or higher
A3-2 (PR) - Body ground
1MΩ or higher
A3-1 (-) - Body ground
1MΩ or higher
Reconnect the air conditioning pressure sensor connector.
Reconnect the air conditioning amplifier connector.
|
|
||||
| OK | |
| 4. INSPECT AIR CONDITIONING AMPLIFIER |
![]() ![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
E11-13 (SG-2) - Body ground
Below 1 Ω
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester Connection
Specified Condition
E11-10 (S5-3) - E11-13 (SG-2)
4.5 to 5.5 V
Reinstall the air conditioning amplifier.
|
|
||||
| OK | |
| 5. INSPECT AIR CONDITIONING PRESSURE SENSOR |
![]() ![]() |
Remove the air conditioning amplifier with its connectors still connected.
Set the manifold gauge.
Warm up the engine.
Turn the A/C switch ON.
Measure the voltage.
- Standard voltage:
Tester Connection
Refrigerant Pressure
Specified Condition
E11-9 (PRE) - E11-13 (SG-2)
0.196 to 3.14 MPa (2.0 to 32 kgf/cm2)
0.76 to 4.74 V
Reinstall the air conditioning amplifier.
|
|
||||
| OK | ||
| ||




