2005-2008 Yaris · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT DRIVE SHAFT DUST COVER

C128946E01
  1. Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.

    SST
    09527-10011  

    NOTICE:
    1. Install the dust cover in the correct orientation.
    2. Do not deform the dust cover.


2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
  1. Install a new snap ring.


3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT
  1. Wrap the spline of the outboard joint shaft with protective tape.

  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle outboard joint boot No. 2 clamp
    2.
    Front axle outboard joint boot
    3.
    Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft and outboard joint boot with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1KR-FE
    82 to 92g (2.9 to 3.2 oz.)
    2SZ-FE
    78 to 88 g (2.8 to 3.1 oz.)
    1ND-TV
    151 to 161 g (5.3 to 5.7 oz.)

  1. Install the outboard joint boot onto the outboard joint shaft groove.

    NOTICE:
    Keep the groove free of grease.


4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. C128947E01
    Place SST onto the boot clamp, press it against the boot and slightly tighten SST.
    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

  1. Remove SST.

  1. C128948E01
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

    NOTICE:
    If the clearance is outside the specified range, retighten it.


5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

C128949E01
  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

  1. Remove SST.

  1. C128950E01
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

    NOTICE:
    If the clearance is outside the specified range, retighten it.


6. INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side)

C128951E01
  1. Install the drive shaft damper onto dimension (A) shown in the illustration.

    Dimension (A):
    Engine Type
    Dimension (A)
    1KR-FE
    396 to 400 mm
    (15.59 to 15.75 in.)
    2SZ-FE
    465 to 469 mm
    (18.31 to 18.46in.)
    1ND-TV
    402 to 406 mm
    (15.83 to 15.98 in.)


7. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side)

C128952E01
  1. Place SST onto the damper clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

  1. Remove SST.

  1. C128953E01
    Using SST, measure the clearance of the damper clamp as shown in the illustration.
    SST
    09240-00020  

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

    NOTICE:
    If the clearance is outside the specified range, retighten it.


8. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install new parts onto the outboard joint shaft in the following order.

    1.
    Front axle inboard joint boot clamp
    2.
    Front axle inboard joint boot
    3.
    Front axle inboard joint boot No. 2 clamp

  1. Fix the outboard joint shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.

  1. F047445E01
    Align the matchmarks and install the tripod joint onto the outboard joint shaft.

    NOTICE:
    Face the serrated side of the tripod joint outward and install it onto the outboard joint end.

  1. Using a brass bar and hammer, install the tripod joint.

    NOTICE:
    1. Do not hit the roller portion.
    2. Keep the tripod joint free of foreign matter.

  1. C130325E01
    Using a snap ring expander, install a new snap ring.

  1. Pack the inboard joint with grease.

    Standard Quantity:
    Engine Type
    Quantity
    1KR-FE
    98 to 112 g (3.5 to 4.0 oz.)
    2SZ-FE
    100 to 114 g (3.5 to 4.0 oz.)
    1ND-TV
    109 to 123 g (3.8 to 4.3 oz.)

  1. C128942E01
    Align the matchmarks and install the inboard joint onto the outboard joint shaft.


9. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.

    NOTICE:
    Keep the grooves free of grease.


10. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

C128940
  1. Using needle-nose pliers, align the concave part with the protrusion of the boot clamp in order to fix it.

    NOTICE:
    1. Do not damage the boot.
    2. Do not deform the claw of the hook.


11. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

C128954E01
  1. Place SST onto the boot clamp, press it against the boot and slightly tighten SST.

    SST
    09521-24010  

  1. Fix SST and tighten it so that the clearance comes to within the specified range.

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

  1. Remove SST.

  1. C128955E01
    Using SST, measure the clearance of the boot clamp as shown in the illustration.
    SST
    09240-00020  

    Standard Clearance:
    0.5 to 1.5 mm (0.020 to 0.059 in.)

    NOTICE:
    If the clearance is outside the specified range, retighten it.


12. INSPECT FRONT DRIVE SHAFT

C128956E01
  1. Check whether the drive shaft dimensions are within the following specifications.

    HINT:
    The following table shows dimension (A) of the drive shaft.

    Dimension (A):
    Engine Type
    LH
    RH
    1KR-FE
    595.8 mm
    (23.46 in.)
    813.3 mm
    (32.02 in.)
    2SZ-FE
    597.1 mm
    (23.51 in.)
    812.1 mm
    (31.97 in.)
    1ND-TV
    586.5 mm
    (23.09 in.)
    827.5 mm
    (32.58 in.)

  1. C128957
    Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    NOTICE:
    Keep the drive shaft level while moving it.

← DISASSEMBLY (from Nov 2005)INSTALLATION (from Nov 2005) →