2005-2008 Yaris · Service Manual BODY ELECTRICAL

Driver Side Seat Belt Warning Light does not Operate

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the ignition switch is on (IG), the main body ECU communicates the status of the front seat inner belt (driver side) to the combination meter assembly using the CAN communication line. When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light on the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the warning light.

WIRING DIAGRAM

B120358E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (Indicat. Light D-seat Belt)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Perform the ACTIVE TEST according to the indication displayed on the tester.

    Combination Meter Assembly:
    Item
    Test Details
    Diagnostic Note
    Indicat. Lamp D-seat Belt
    Front driver seat belt warning light / OFF or ON
    -

    OK:
    Front driver seat belt warning light comes on



NG
REPLACE COMBINATION METER ASSEMBLY
OK


2. INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

  1. B129964E05
    LHD:
    1. Disconnect the D35 front seat inner belt assembly (driver side) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (E) - 2 (+)
      Tongue plate fastened
      10 kΩ or higher
      1 (E) - 2 (+)
      Tongue plate unfastened
      Below 1 Ω

    3. Reconnect the front seat inner belt assembly (driver side) connector.

  1. RHD:

    1. Disconnect the D34 front seat inner belt assembly (driver side) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (E) - 2 (+)
      Tongue plate fastened
      10 kΩ or higher
      1 (E) - 2 (+)
      Tongue plate unfastened
      Below 1 Ω

    3. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - MAIN BODY ECU)

  1. B129965E01
    LHD (w/ Entry and start system):
    1. Disconnect the J35 front seat inner belt assembly (driver side) connector.

    2. Disconnect the D64 main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      D64-26 (DBKL) - J35-2 (+)
      Below 1 Ω
      D64-26 (DBKL) or J35-2 (+) - Body ground
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (driver side) connector.

    5. Reconnect the main body ECU connector.

  1. LHD (w/o Entry and start system):

    1. Disconnect the J35 front seat inner belt assembly (driver side) connector.

    2. Disconnect the D33 main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      D33-9 (DBKL) - J35-2 (+)
      Below 1 Ω
      D33-9 (DBKL) or J35-2 (+) - Body ground
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (driver side) connector.

    5. Reconnect the main body ECU connector.

  1. RHD (w/ Entry and start system):

    1. Disconnect the J34 front seat inner belt assembly (driver side) connector.

    2. Disconnect the D64 main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      D64-26 (DBKL) - J34-2 (+)
      Below 1 Ω
      D64-26 (DBKL) or J34-2 (+) - Body ground
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (driver side) connector.

    5. Reconnect the main body ECU connector.

  1. RHD (w/o Entry and start system):

    1. Disconnect the J34 front seat inner belt assembly (driver side) connector.

    2. Disconnect the D33 main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      D33-9 (DBKL) - J34-2 (+)
      Below 1 Ω
      D33-9 (DBKL) or J34-2 (+) - Body ground
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (driver side) connector.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - BODY GROUND)

  1. B129966E04
    LHD:
    1. Disconnect the J35 front seat inner belt assembly (driver side) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      J35-1 (E) - Body ground
      Below 1 Ω

    3. Reconnect the front seat inner belt assembly (driver side) connector.

  1. RHD:

    1. Disconnect theJ34 front seat inner belt assembly (driver side) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Specified Condition
      J34-1 (E) - Body ground
      Below 1 Ω

    3. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Warning Buzzer does not Sound (from Aug 2005)Front Passenger Side Seat Belt Warning Light Malfunction (from Aug 2005) →