Front Passenger Side Seat Belt Warning Light Malfunction
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the ignition switch is on (IG) and the passenger seat is occupied, the occupant detection sensor communicates the status of the front seat inner belt assembly (passenger side) to the combination meter assembly. When the front seat belt is unfastened, the combination meter assembly flashes the front passenger seat belt warning light on the instrument panel cluster finish panel end. When the seat belt is fastened, the combination meter stops flashing the front passenger seat belt warning light.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (Indicat. Lamp P-seat Belt) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Perform the ACTIVE TEST according to the indication displayed on the tester.
- Combination Meter Assembly:
Item
Test details
Diagnostic Note
Indicat. Lamp P-seat Belt
Front passenger seat belt warning light/ OFF or ON
-
- OK:
- Front passenger seat belt warning light come on.
|
|
||||
| OK | |
| 2. INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE) |
LHD:

Disconnect the J34 front seat inner belt assembly (passenger side) connector.
Disconnect the occupant detection sensor connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 (E) - Occupant detection sensor connector-1
Tongue plate fastened
10 kΩ or higher
1 (E) - Occupant detection sensor connector-1
Tongue plate unfastened
Below 1Ω
1 (E) - Body ground
Always
10 kΩ or higher
Occupant detection sensor connector-1 - Body ground
Always
10 kΩ or higher
2 (+) - Occupant detection sensor connector-3
Always
Below 1Ω
2 (+) or Occupant detection sensor connector-3 - Body ground
Always
10 kΩ or higher
Reconnect the front seat inner belt assembly (passenger side) connector.
Reconnect the occupant detection sensor connector.
RHD:
Disconnect the J35 front seat inner belt assembly (passenger side) connector.
Disconnect the occupant detection sensor connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 (E) - Occupant detection sensor connector-1
Tongue plate fastened
10 kΩ or higher
1 (E) - Occupant detection sensor connector-1
Tongue plate unfastened
Below 1Ω
1 (E) - Body ground
Always
10 kΩ or higher
Occupant detection sensor connector-1 - Body ground
Always
10 kΩ or higher
2 (+) - Occupant detection sensor connector-3
Always
Below 1Ω
2 (+) or Occupant detection sensor connector-3 - Body ground
Always
10 kΩ or higher
Reconnect the front seat inner belt assembly (passenger side) connector.
Reconnect the occupant detection sensor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER , BODY GROUND) |
LHD:

Disconnect the J34 front seat inner belt assembly (passenger side) connector.
Disconnect the D1 combination meter assembly connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
J34-2 (+) - D1-10 (P/SB)
Below 1 Ω
J34-2 (+) or D1-10 (P/SB) - Body ground
10 kΩ or higher
J34-1 (E) - Body ground
Below 1 Ω
Reconnect the front seat inner belt assembly (passenger side) connector.
Reconnect the combination meter assembly connector.
RHD:
Disconnect the J35 front seat inner belt assembly (passenger side) connector.
Disconnect the D1 combination meter assembly connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
J35-2 (+) - D1-10 (P/SB)
Below 1 Ω
J35-2 (+) or D1-10 (P/SB) - Body ground
10 kΩ or higher
J35-1 (E) - Body ground
Below 1 Ω
Reconnect the front seat inner belt assembly (passenger side) connector.
Reconnect the combination meter assembly connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (GAUGE) |
Remove the GAUGE fuse from the main body ECU.
Measure the resistance.
- Standard resistance:
- Below 1 Ω
Remove the GAUGE fuse.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (FUSE - FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY) |


TMC made (for Europe):
Disconnect the D27 front passenger seat belt warning light connector.
Disconnect the 4S main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4S-15 - D27-6 (IG+)
Below 1 Ω
4S-15 or D27-6 (IG+) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and main body ECU connectors.
TMC made (for except Europe):
Disconnect the D59 front passenger seat belt warning light connector.
Disconnect the 4S main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4S-15 - D59-1 (IG+)
Below 1 Ω
4S-15 or D59-1 (IG+) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and main body ECU connectors.
TMMF made:
Disconnect the D78 front passenger seat belt warning light connector.
Disconnect the 4S main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
4S-15 - D78-4 (IG+)
Below 1 Ω
4S-15 or D78-4 (IG+) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and main body ECU connectors.
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (SEAT BELT WARNING LIGHT - COMBINATION METER) |


TMC made (for Europe):
Disconnect the D27 front passenger seat belt warning light connector.
Disconnect the D2 combination meter assembly connector.
Measure the resistance.
- Standard resistance:
- LHD:
Tester Connection
Specified Condition
D27-3 (PBEW) - D2-9 (PBLT)
Below 1 Ω
D27-3 (PBEW) or D2-9 (PBLT) - Body ground
10 kΩ or higher
- RHD:
Tester Connection
Specified Condition
D27-3 (PBEW) - D2-16 (PBLT)
Below 1 Ω
D27-3 (PBEW) or D2-16 (PBLT) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and combination meter connectors.
TMC made (for except Europe):
Disconnect the D59 front passenger seat belt warning light connector.
Disconnect the D2 combination meter assembly connector.
Measure the resistance.
- Standard resistance:
- LHD:
Tester Connection
Specified Condition
D59-3 (PBEW) - D2-9 (PBLT)
Below 1 Ω
D59-3 (PBEW) or D2-9 (PBLT) - Body ground
10 kΩ or higher
- RHD:
Tester Connection
Specified Condition
D59-3 (PBEW) - D2-16 (PBLT)
Below 1 Ω
D59-3 (PBEW or D2-16 (PBLT) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and combination meter connectors.
TMMF made:
Disconnect the D78 front passenger seat belt warning light connector.
Disconnect the D2 combination meter assembly connector.
Measure the resistance.
- Standard resistance:
- LHD:
Tester Connection
Specified Condition
D78-3 (PBEW) - D2-9 (PBLT)
Below 1 Ω
D78-3 (PBEW) or D2-9 (PBLT) - Body ground
10 kΩ or higher
- RHD:
Tester Connection
Specified Condition
D78-3 (PBEW) - D2-16 (PBLT)
Below 1 Ω
D78-3 (PBEW) or D2-16 (PBLT) - Body ground
10 kΩ or higher
Reconnect the front passenger seat belt warning light and combination meter connectors.
|
|
||||
| OK | |
| 7. INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY |
Remove the front passenger seat belt warning light assembly.
Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

TMC made (for Europe):
- Standard:
Measurement Condition
Specified Condition
Positive battery - Terminal 6 (lG+) Negative battery - Terminal 3 (PBEW)
Front passenger seat belt warning light illuminates
TMC made (for except Europe):

- Standard:
Measurement Condition
Specified Condition
Positive battery - Terminal 1 (lG+) Negative battery - Terminal 3 (PBEW)
Front passenger seat belt warning light Illuminates
TMMF made:

- Standard:
Measurement Condition
Specified Condition
Positive battery - Terminal 4 (lG+) Negative battery - Terminal 3 (PBEW)
Front passenger seat belt warning light illuminates
Reinstall the front passenger seat belt warning light assembly.
|
|
||||
| OK | ||
| ||
