2005-2008 Yaris · Service Manual RESTRAINTS

Front Passenger Side Seat Belt Warning Light Malfunction

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the ignition switch is on (IG) and the passenger seat is occupied, the occupant detection sensor communicates the status of the front seat inner belt assembly (passenger side) to the combination meter assembly. When the front seat belt is unfastened, the combination meter assembly flashes the front passenger seat belt warning light on the instrument panel cluster finish panel end*1 or hazard warning signal switch assembly*2. When the seat belt is fastened, the combination meter stops flashing the front passenger seat belt warning light.

HINT:
*1: Hatchback
*2: Sedan


WIRING DIAGRAM

B141545E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (Indicat. Lamp P-seat Belt)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Perform the ACTIVE TEST according to the indication displayed on the tester.

    Combination Meter Assembly:
    Item
    Test details
    Diagnostic Note
    Indicat. Lamp P-seat Belt
    Front passenger seat belt warning light/ OFF or ON
    -

    OK:
    Front passenger seat belt warning light comes on.



NG
Go to step 4
OK


2. INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)

  1. B120593E03
    LHD:
    1. Disconnect the J34 front seat inner belt assembly (passenger side) connector.

    2. Disconnect the occupant detection sensor connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (E) - Occupant detection sensor connector-1
      Tongue plate fastened
      10 kΩ or higher
      1 (E) - Occupant detection sensor connector-1
      Tongue plate unfastened
      Below 1Ω
      1 (E) - Body ground
      Always
      10 kΩ or higher
      Occupant detection sensor connector-1 - Body ground
      Always
      10 kΩ or higher
      2 (+) - Occupant detection sensor connector-3
      Always
      Below 1Ω
      2 (+) or Occupant detection sensor connector-3 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (passenger side) connector.

    5. Reconnect the occupant detection sensor connector.

  1. RHD:

    1. Disconnect the J35 front seat inner belt assembly (passenger side) connector.

    2. Disconnect the occupant detection sensor connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (E) - Occupant detection sensor connector-1
      Tongue plate fastened
      10 kΩ or higher
      1 (E) - Occupant detection sensor connector-1
      Tongue plate unfastened
      Below 1Ω
      1 (E) - Body ground
      Always
      10 kΩ or higher
      Occupant detection sensor connector-1 - Body ground
      Always
      10 kΩ or higher
      2 (+) - Occupant detection sensor connector-3
      Always
      Below 1Ω
      2 (+) or Occupant detection sensor connector-3 - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the front seat inner belt assembly (passenger side) connector.

    5. Reconnect the occupant detection sensor connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER, BODY GROUND)

  1. B141565E01
    LHD:
    1. Disconnect the J34 front seat inner belt assembly (passenger side) connector.

    2. Disconnect the D1 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      J34-2 (+) - D1-10 (P/SB)
      Below 1 Ω
      J34-2 (+) or D1-10 (P/SB) - Body ground
      10 kΩ or higher
      J34-1 (E) - Body ground
      Below 1 Ω

    4. Reconnect the front seat inner belt assembly (passenger side) connector.

    5. Reconnect the combination meter assembly connector.

  1. RHD:

    1. Disconnect the J35 front seat inner belt assembly (passenger side) connector.

    2. Disconnect the D1 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      J35-2 (+) - D1-10 (P/SB)
      Below 1 Ω
      J35-2 (+) or D1-10 (P/SB) - Body ground
      10 kΩ or higher
      J35-1 (E) - Body ground
      Below 1 Ω

    4. Reconnect the front seat inner belt assembly (passenger side) connector.

    5. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OCCUPANT DETECTION SENSOR

4. INSPECT FUSE (GAUGE)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Remove the GAUGE fuse.



NG
REPLACE FUSE
OK


5. CHECK HARNESS AND CONNECTOR (FUSE - FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY)
B141566E01
  1. TMC made, Hatchback (for Europe):

    1. Disconnect the D27 front passenger seat belt warning light connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D27-6 (IG+)
      Below 1 Ω
      4S-15 or D27-6 (IG+) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.

  1. TMC made, Hatchback (for except Europe):

    1. Disconnect the D59 front passenger seat belt warning light connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D59-1 (IG+)
      Below 1 Ω
      4S-15 or D59-1 (IG+) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.

  1. TMMF made, Hatchback:

    1. Disconnect the D78 front passenger seat belt warning light connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D78-4 (IG+)
      Below 1 Ω
      4S-15 or D78-4 (IG+) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.

  1. TMC made, Sedan:

    1. Disconnect the D85 hazard warning signal switch assembly connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D85-6 (IG+)
      Below 1 Ω
      4S-15 or D85-6 (IG+) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (SEAT BELT WARNING LIGHT - COMBINATION METER, BODY GROUND)
B147606E01
  1. TMC made, Hatchback (for Europe):

    1. Disconnect the D27 front passenger seat belt warning light connector.

    2. Disconnect the D2 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      LHD:
      Tester Connection
      Specified Condition
      D27-3 (PBEW) - D2-9 (PBLT)
      Below 1 Ω
      D27-3 (PBEW) - D2-9 (PBLT) - Body ground
      10 kΩ or higher
      RHD:
      Tester Connection
      Specified Condition
      D27-3 (PBEW) - D2-16 (PBLT)
      Below 1 Ω
      D27-3 (PBEW) or D2-16 (PBLT) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.

  1. TMC made, Hatchback (for except Europe):

    1. Disconnect the D59 front passenger seat belt warning light connector.

    2. Disconnect the D2 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      LHD:
      Tester Connection
      Specified Condition
      D59-3 (PBEW) - D2-9 (PBLT)
      Below 1 Ω
      D59-3 (PBEW) or D2-9 (PBLT) - Body ground
      10 kΩ or higher
      RHD:
      Tester Connection
      Specified Condition
      D59-3 (PBEW) - D2-16 (PBLT)
      Below 1 Ω
      D59-3 (PBEW) or D2-16 (PBLT) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.

  1. TMMF made, Hatchback:

    1. Disconnect the D78 front passenger seat belt warning light connector.

    2. Disconnect the D2 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      LHD:
      Tester Connection
      Specified Condition
      D78-3 (PBEW) - D2-9 (PBLT)
      Below 1 Ω
      D78-3 (PBEW) or D2-9 (PBLT) - Body ground
      10 kΩ or higher
      RHD:
      Tester Connection
      Specified Condition
      D78-3 (PBEW) - D2-16 (PBLT)
      Below 1 Ω
      D78-3 (PBEW) or D2-16 (PBLT) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.

  1. TMC made, Sedan:

    1. Disconnect the D85 hazard warning signal switch assembly connector.

    2. Disconnect the D84 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-8 (PBEW) - D84-9 (PBLT)
      Below 1 Ω
      D85-8 (PBEW) or D84-9 (PBLT) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY

  1. B127790E03
    TMC made, Hatchback (for Europe):
    1. Remove the front passenger seat belt warning light assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 6 (lG+) Negative battery - Terminal 3 (PBEW)
      Front passenger seat belt warning light illuminates

    3. Reinstall the front passenger seat belt warning light assembly.

  1. B127791E02
    TMC made, Hatchback (for except Europe):
    1. Remove the front passenger seat belt warning light assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1 (lG+) Negative battery - Terminal 3 (PBEW)
      Front passenger seat belt warning light Illuminates

    3. Reinstall the front passenger seat belt warning light assembly.

  1. B133337E01
    TMMF made, Hatchback:
    1. Remove the front passenger seat belt warning light assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 4 (lG+) Negative battery - Terminal 3 (PBEW)
      Front passenger seat belt warning light illuminates

    3. Reinstall the front passenger seat belt warning light assembly.

  1. B143252E01
    TMC made, Sedan:
    1. Remove the hazard warning signal switch assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 6 (lG+) Negative battery - Terminal 8 (PBEW)
      Front passenger seat belt warning light Illuminates

    3. Reinstall the front passenger seat belt warning light assembly.



NG
REPLACE FRONT PASSENGER SEAT BELT WARNING LIGHT
OK

REPLACE COMBINATION METER ASSEMBLY


← Driver Side Seat Belt Warning Light does not Operate (from Aug 2005)COMPONENTS (from Jan 2006) →