Driver Side Seat Belt Warning Light does not Operate
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
When the ignition switch is on (IG), the main body ECU communicates the status of the front seat inner belt (driver side) to the combination meter assembly using the CAN communication line. When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light on the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the warning light.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (Indicat. Light D-seat Belt) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Perform the ACTIVE TEST according to the indication displayed on the tester.
- Combination Meter Assembly:
Item
Test Details
Diagnostic Note
Indicat. Lamp D-seat Belt
Front driver seat belt warning light / OFF or ON
-
- OK:
- Front driver seat belt warning light comes on
|
|
||||
| OK | |
| 2. INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) |
LHD:

Disconnect the D35 front seat inner belt assembly (driver side) connector.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified Condition
1 (E) - 2 (+)
Tongue plate fastened
10 kΩ or higher
1 (E) - 2 (+)
Tongue plate unfastened
Below 1 Ω
Reconnect the front seat inner belt assembly (driver side) connector.
RHD:
Disconnect the D34 front seat inner belt assembly (driver side) connector.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified Condition
1 (E) - 2 (+)
Tongue plate fastened
10 kΩ or higher
1 (E) - 2 (+)
Tongue plate unfastened
Below 1 Ω
Reconnect the front seat inner belt assembly (driver side) connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - MAIN BODY ECU) |
LHD (w/ Entry and start system):

Disconnect the J35 front seat inner belt assembly (driver side) connector.
Disconnect the D64 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
D64-26 (DBKL) - J35-2 (+)
Below 1 Ω
D64-26 (DBKL) or J35-2 (+) - Body ground
10 kΩ or higher
Reconnect the front seat inner belt assembly (driver side) connector.
Reconnect the main body ECU connector.
LHD (w/o Entry and start system):
Disconnect the J35 front seat inner belt assembly (driver side) connector.
Disconnect the D33 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
D33-9 (DBKL) - J35-2 (+)
Below 1 Ω
D33-9 (DBKL) or J35-2 (+) - Body ground
10 kΩ or higher
Reconnect the front seat inner belt assembly (driver side) connector.
Reconnect the main body ECU connector.
RHD (w/ Entry and start system):
Disconnect the J34 front seat inner belt assembly (driver side) connector.
Disconnect the D64 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
D64-26 (DBKL) - J34-2 (+)
Below 1 Ω
D64-26 (DBKL) or J34-2 (+) - Body ground
10 kΩ or higher
Reconnect the front seat inner belt assembly (driver side) connector.
Reconnect the main body ECU connector.
RHD (w/o Entry and start system):
Disconnect the J34 front seat inner belt assembly (driver side) connector.
Disconnect the D33 main body ECU connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
D33-9 (DBKL) - J34-2 (+)
Below 1 Ω
D33-9 (DBKL) or J34-2 (+) - Body ground
10 kΩ or higher
Reconnect the front seat inner belt assembly (driver side) connector.
Reconnect the main body ECU connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - BODY GROUND) |
LHD:

Disconnect the J35 front seat inner belt assembly (driver side) connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
J35-1 (E) - Body ground
Below 1 Ω
Reconnect the front seat inner belt assembly (driver side) connector.
RHD:
Disconnect theJ34 front seat inner belt assembly (driver side) connector.
Measure the resistance.
- Standard resistance:
Tester connection
Specified Condition
J34-1 (E) - Body ground
Below 1 Ω
Reconnect the front seat inner belt assembly (driver side) connector.
|
|
||||
| OK | ||
| ||
