2005-2008 Yaris · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2005

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


1. INSTALL ROOF SIDE RAIL BRACKET RH

C121174E01
  1. Insert the 2 hooks into the body holes and install the roof side rail bracket.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the wire harness clamp.


2. INSTALL CURTAIN SHIELD AIRBAG BRACKET RH

C121175E01
  1. Insert the 2 hooks into the body holes and install the curtain shield airbag bracket.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


3. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY
  1. Tighten the 2 bolts A.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }

  1. Tighten the 4 screws B.

  1. Install front strap C.

    NOTICE:
    Attach double sided tape to the indicated area, with the strap pulled downward. When installing the strap, make sure that the front pillar garnish installation holes are not hidden by the strap of the curtain shield airbag.

  1. Tighten the 2 bolts D.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


    C121176E02

  1. B108343E01
    Connect the airbag connector.

    NOTICE:
    Lock the locking button securely.


4. INSTALL ROOF HEADLINING ASSEMBLY

  1. B114544
    Pull the roof headlining back into the vehicle through the back door.

  1. w/ Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Engage the 4 hooks and install the roof headlining.
      2. Install the clip.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Engage the 4 hooks and install the roof headlining.
      2. Install the 2 clips.

      B119919E01

  1. w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Engage the 2 claws and the 4 hooks and install the roof headlining.
      2. Install the clip.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Engage the 2 claws and the 4 hooks and install the roof headlining.

      2. Install the 2 clips.

        B119920E01

  1. B114512
    Install the 2 connectors.

  1. Connect the 2 connectors.

  1. Install the antenna cord onto the antenna cord clamp.

  1. B114511
    for LHD:

    1. Connect the connector.

    2. Install the wiring harness clamp.

  1. B114320
    for RHD:

    1. Connect the connector.

    2. Install the No. 1 roof wire into the claw of the junction block.

    3. B114319
      Install the wiring harness clamp.


5. INSTALL INSTRUMENT PANEL BOX (for LHD)

B108189E01
  1. Insert the stopper of the instrument panel box from the cutout of the instrument panel lower.

  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.


6. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


7. INSTALL SWITCH HOLE BASE (for LHD)

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


8. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


9. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


10. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


11. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


12. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


13. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


14. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


15. INSTALL MAP LIGHT ASSEMBLY

  1. B114310
    Connect the map light connector.

  1. B114346
    Engage the 4 claws and install the map light.


16. INSTALL ROOM LIGHT ASSEMBLY

  1. B114347
    Engage the 4 claws and install the room light switch base.

  1. Install the roof wire onto the claw of the room light.

  1. B114348
    Engage the 4 claws and install the room light.

  1. B124366
    Engage the 4 claws and install the 2 covers.

  1. B114349
    Engage the 4 claws and install the room light lens.


17. INSTALL VISOR HOLDER RH

  1. B114350E01
    Engage the 2 claws by turning the visor holder clockwise between 60 to 120° and install the visor holder.


18. INSTALL VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.


19. INSTALL VISOR ASSEMBLY RH

  1. B114304
    Engage the 2 springs and install the visor.

  1. Install the visor shaft into the visor holder.

  1. B114351
    Engage the 4 claws and install the visor bracket cover.


20. INSTALL VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


21. INSTALL ASSIST GRIP SUB-ASSEMBLY

B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Engage the 2 springs and install the assist grip.


22. INSTALL SEAT BELT ANCHOR COVER CAP (for Rear Center Seat Belt 3 Point Type)

  1. B114467
    Engage the 4 claws and install the seat belt anchor cover.


23. INSTALL REAR ROOF SIDE RAIL GARNISH RH

  1. B114508
    Engage the 4 clips and install the rear roof side rail garnish.


24. INSTALL REAR ROOF SIDE RAIL GARNISH LH

  1. B114506E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114507
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.


25. INSTALL ROOF SIDE INNER GARNISH RH

  1. B114504E01
    w/ Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Install a new special clip onto the roof side inner garnish.
      2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      3. Engage the 4 clips and the claw and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114505
    w/o Curtain Shield Airbag:

    1. for 3 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.


26. INSTALL ROOF SIDE INNER GARNISH LH

  1. B114506E01
    w/ Curtain Shield Airbag:

    1. Install a new special clip onto the roof side inner garnish.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.

  1. B114507
    w/o Curtain Shield Airbag:

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.


27. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt)

HINT:
Use the same procedure as for the RH side.


28. INSTALL CENTER PILLAR UPPER GARNISH RH

  1. B114503
    Engage the 2 clips and install the center pillar upper garnish.


29. INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:
Use the same procedure as for the RH side.


30. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B114479
    Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


31. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


32. INSTALL SEAT BELT ANCHOR COVER CAP RH

  1. B114478
    Engage the 3 claws and install the seat belt anchor cover cap.


33. INSTALL SEAT BELT ANCHOR COVER CAP (for 3 Point Type Rear Center Seat Belt)

  1. B114467
    Engage the 4 claws and install the seat belt anchor cover.


34. INSTALL DECK SIDE TRIM PANEL ASSEMBLY RH

  1. B114501
    Engage the 3 clips and the 3 claws and install the deck side trim panel.

  1. Tighten the 3 screws.


35. INSTALL DECK SIDE TRIM PANEL ASSEMBLY LH

  1. B114502
    Connect the deck side room light connector.

  1. Engage the 3 clips and the 3 claws and install the deck side trim panel.

  1. Tighten the 3 screws.


36. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

  1. B114500
    Engage the clip and install the anchor plate.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


37. INSTALL REAR SEAT OUTER BELT ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


38. INSTALL REAR DECK TRIM COVER

  1. B114283
    for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.

  1. B117692
    for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.


39. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

  1. B114499
    Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.

  1. B114498
    Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.


40. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.


41. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (w/ Seat Belt Bar)

  1. B114759
    Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }


42. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY LH (w/ Seat Belt Bar)

HINT:
Use the same procedure as for the RH side.


43. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B114546E01
    Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Yellow
    LH side
    White


44. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.


45. INSTALL COWL SIDE TRIM BOARD RH

  1. B114285
    Engage the claw and stud bolt and install the cowl side trim board.


46. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.


47. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH

  1. B114571
    Engage the 4 claws and install the instrument panel under cover.


48. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH

  1. B114572
    Engage the 3 claws and install the instrument panel under cover.

  1. Tighten the 2 screws.


49. INSTALL FRONT DOOR SCUFF PLATE RH

  1. B114494
    Engage the 8 claws and install the front door scuff plate.


50. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.


51. INSTALL REAR SEAT ASSEMBLY LH

  1. B126922E01
    Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B114740E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


52. INSTALL REAR SEAT ASSEMBLY RH

  1. B114684E01
    Insert the 2 location pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B114660E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 2 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


53. INSTALL NO.2 SEAT LEG COVER

  1. B114739
    Engage the 3 claws and install the No. 2 rear seat leg cover.


54. INSTALL NO.1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover (Click here).

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover (Click here).


55. INSTALL DECK FLOOR BOX RH (w/ Deck Board)

  1. B106446
    Set the deck floor box and lock the 2 knobs.


56. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.


57. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B119913
    Install the spare wheel cover.


58. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


59. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B119912
    Install the rear floor carpet.


60. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


61. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


62. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2005)DISPOSAL (from Aug 2005) →