REMOVAL
Removal / installation · Vehicles built from Aug 2005
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() ![]() |
with CD player
Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.
- NOTICE:
- To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.
- HINT:
- Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.
Disconnect the connector and remove the instrument panel finish panel end LH.
Except CD player

Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.
- NOTICE:
- To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.
- HINT:
- Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.
Disconnect the connector and remove the instrument panel finish panel end LH.
| 3. REMOVE INSTRUMENT PANEL FINISH PANEL END RH |
![]() ![]() |
with CD player
Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.
- NOTICE:
- To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.
- HINT:
- Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.
Disconnect the connector and remove the instrument panel finish panel end RH.
Except CD player

Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.
- NOTICE:
- To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.
- HINT:
- Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.
Disconnect the connector and remove the instrument panel finish panel end RH.
| 4. REMOVE INSTRUMENT CLUSTER FINISH PANEL |
![]() ![]() |
- NOTICE:
- Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.
Disengage the 2 claws and 5 clips.

After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

Disengage the 3 A claws and remove the instrument cluster finish panel.
| 5. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY (w/ Cassette Tape Player) |
![]() ![]() |
Disengage the 2 claws and 4 clips and remove the instrument cluster finish panel center.
- NOTICE:
- Grip the rib portion of the instrument cluster finish panel center by hand to remove it.
- To avoid breakage of the instrument cluster finish panel center when removing it, do not apply excessive force to the register or pull out the rink or panel portions.
- Grip the rib portion of the instrument cluster finish panel center by hand to remove it.
| 6. REMOVE RADIO RECEIVER ASSEMBLY |
![]() ![]() |
w/ Cassette Tape Player:
Remove the 4 screws.
Disconnect the connectors and remove the radio receiver.
w/ CD Player:

Remove the 4 screws.
Disengage the 2 claws and 4 clips and the radio receiver.
- NOTICE:
- Grip the rib portion of the radio receiver by hand to remove it.
- To avoid breakage of the radio receiver when removing it, do not apply excessive force to the register or pull out the rink or panel portions.
- Grip the rib portion of the radio receiver by hand to remove it.
Disconnect the connectors.
| 7. REMOVE NO. 2 RADIO BRACKET |
![]() ![]() |
w/ Cassette Tape Player:
Remove the 4 screws and remove the radio bracket and the radio receiver panel.
w/ CD Player:

Remove the 4 screws and remove the radio bracket.
| 8. REMOVE NO. 1 RADIO BRACKET |
![]() ![]() |
w/ Cassette Tape Player:
Remove the 4 screws and remove the radio bracket and the radio receiver panel.
w/ CD Player:

Remove the 4 screws and remove the radio bracket.







