2005-2008 Yaris · Service Manual RESTRAINTS

B1651/33 Manual Cut off Switch Trouble

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The passenger airbag manual cut-off switch circuit consists of parts including the center airbag sensor assembly and the airbag cut-off switch.
DTC B1651/33 is set when a malfunction is detected in the airbag cut off switch circuit.
DTC No.
DTC Detecting Conditions
Trouble Areas
B1651/33
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in airbag cut-off switch circuit for 2 seconds
  1. Airbag cut-off switch malfunction
  1. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  1. Passenger airbag manual cut off switch
  1. Center airbag sensor assembly

WIRING DIAGRAM

H100145E02

INSPECTION PROCEDURE

CAUTION:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connector from the steering pad.
  5. Disconnect the connector from the front seat outer belt assembly LH.
  6. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.

  7. Disconnect the connector from the front passenger airbag assembly.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.
  12. Disconnect the connector from the driver side knee airbag assembly.

1. CHECK DTC
H101852E05
  1. Turn the ignition switch on (IG).

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

    HINT:
    DTCs other than B1651/33 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2. CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the airbag cut-off switch.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. INSPECT AIRBAG CUT-OFF SWITCH
H100191E01
  1. Disconnect the D57 passenger airbag manual cut-off switch connector.

  1. Measure the resistance.

    Standard resistance:
    Switch Condition
    Tester Connection
    Specified Condition
    OFF
    1 (PMC-) -
    2 (PMC+)
    80 to 120Ω
    ON
    1 (PMC-) -
    2 (PMC+)
    320 to 480Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH
OK


4. CHECK INSTRUMENT PANEL WIRE (FOR OPEN)
H100193E06
  1. Disconnect the instrument panel wire connector from the airbag cut-off switch.

  1. Using a service wire, connect D57-1 (PMC-) and D57-2 (PMC+) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) -
    D16-12 (MSW-)
    Always
    Below 1Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK INSTRUMENT PANEL WIRE (FOR SHORT)
H100192E05
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) -
    D16-12 (MSW-)
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK INSTRUMENT PANEL WIRE (TO B+)
H100192E06
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+)-
    Body ground
    Ignition switch on (IG)
    Below 1 V
    D16-12 (MSW-) -
    Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7. CHECK INSTRUMENT PANEL WIRE (TO GROUND)
H100192E07
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-11 (MSW+) -
    Body ground
    Always
    1 MΩ or Higher
    D16-12 (MSW-) -
    Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY
H101852E06
  1. Connect the connectors to the center airbag sensor assembly and airbag cut-off switch.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

    HINT:
    DTCs other than B1651/33 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B1635/24 Front Passenger Side Rear Airbag Sensor Circuit Malfunction (from Aug 2005)B1660/43 Passenger Airbag OFF Indicator Circuit Malfunction (from Aug 2005) →