2005-2008 Yaris · Service Manual RESTRAINTS

B1660/43 Passenger Airbag OFF Indicator Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The passenger airbag OFF indicator circuit consists of the center airbag sensor assembly and the front passenger seat belt warning light.
This circuit indicates the operation condition of the front passenger airbag assembly, the front passenger side front seat side airbag assembly and passenger side seat belt pretensioner.
DTC B1660/43 is set when a malfunction is detected in the passenger airbag OFF indicator circuit.
DTC No.
DTC Detecting Conditions
Trouble Areas
B1660/43
  1. Center airbag sensor assembly detects line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in passenger airbag OFF indicator circuit for 2 seconds
  2. Front passenger seat belt warning light malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Front passenger seat belt warning light (Passenger airbag OFF Indicator)
  3. Center airbag sensor assembly

WIRING DIAGRAM

H102122E01
H102123E01

INSPECTION PROCEDURE

NOTICE:
In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the center airbag sensor assembly.
  4. Disconnect the connector from the steering pad.
  5. Disconnect the connector from the front seat outer belt assembly LH.
  6. Disconnect the connector from the front seat outer belt assembly RH.

    HINT:
    Skip the following steps if side airbags, curtain shield airbags, front passenger airbag and a knee airbag are not fitted.

  7. Disconnect the connector from the front passenger airbag assembly.
  8. Disconnect the connector from the front seat side airbag assembly LH.
  9. Disconnect the connector from the front seat side airbag assembly RH.
  10. Disconnect the connector from the curtain shield airbag assembly LH.
  11. Disconnect the connector from the curtain shield airbag assembly RH.
  12. Disconnect the connector from the driver side knee airbag assembly.

1. CHECK PASSENGER AIRBAG OFF INDICATOR OPERATION
  1. Turn the ignition switch on (IG).

  1. Check the passenger airbag OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag OFF indicator (Click here).

    H100160E01

    Result:
    OFF Indicator Illumination
    Proceed To
    Always ON
    A
    OFF
    B



B
Go to step 7
A


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front passenger seat belt warning light.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


3. CHECK FRONT PASSENGER SEAT BELT WARNING LIGHT
H100931
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Check the passenger airbag OFF indicator operation.

    OK:
    Passenger airbag OFF indicator comes on.



OK
Go to step 12
NG


4. CHECK INSTRUMENT PANEL WIRE (FOR OPEN)
H102124E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the front passenger seat belt warning light and center airbag sensor assembly.

  1. Measure the resistance.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) - D27-5 (P-AB)*1
    Always
    Below 1 Ω
    D16-17 (P-AB) - D78-6 (P-AB)*2
    Always
    Below 1 Ω

    *1: TMC made*2: TMMF made



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK INSTRUMENT PANEL WIRE (TO B+)
H100896E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) -Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK INSTRUMENT PANEL WIRE (TO GROUND)
H100896E04
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) -Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE FRONT PASSENGER SEAT BELT WARNING LIGHT

7. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the hazard warning signal switch assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS
OK


8. CHECK INSTRUMENT PANEL WIRE (FOR OPEN)
H102124E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the front passenger seat belt warning light and center airbag sensor assembly.

  1. Measure the resistance.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) - D27-5 (P-AB)*1
    Always
    Below 1 Ω
    D16-17 (P-AB) - D78-6 (P-AB)*2
    Assembly
    Below 1 Ω

    *1: TMC made*2: TMMF made



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


9. CHECK INSTRUMENT PANEL WIRE (TO B+)
H100896E04
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


10. CHECK INSTRUMENT PANEL WIRE (TO GROUND)
H100896E04
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance.

    Standard resistance:
    Terminal Connection
    Condition
    Specified Condition
    D16-17 (P-AB) - Body ground
    Always
    1 MΩ or Higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


11. CHECK WIRE HARNESS (POWER SOURCE)
H102125E01
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage.

    Standard voltage:
    Terminal Connection
    Condition
    Specified Condition
    D27-6 (IG+) - Body ground*1
    Ignition switch on (IG)
    10 to 14 V
    D78-4 (IG+) - Body ground*2
    Ignition switch on (IG)
    10 to 14 V

    *1: TMC made*2: TMMF made



NG
REPAIR OR REPLACE POWER SOURCE CIRCUIT
OK


12. CHECK FRONT PASSENGER SEAT BELT WARNING LIGHT
H102126E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the front passenger seat belt warning light.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. TMC made:Using a service wire, connect D27-5 (P-AB) and D27-4 (ILL-) of front passenger seat belt warning light connector.

  1. TMMF made:Using a service wire, connect D78-6 (P-AB) and D78-5 (ILL-) of front passenger seat belt warning right connector.

  1. Turn the ignition switch on (IG).

  1. Check the passenger airbag OFF indicator operation.

    OK:
    Passenger airbag OFF indicator comes on



NG
REPLACE FRONT PASSENGER SEAT BELT WARNING LIGHT
OK


13. CHECK CENTER AIRBAG SENSOR ASSEMBLY
H100895E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Connect the connector to the center airbag sensor assembly.

  1. Connect the connector to the front passenger seat belt warning light.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660/43 is not output.

    HINT:
    DTCs other than B1660/43 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B1651/33 Manual Cut off Switch Trouble (from Aug 2005)B1662/45 Indicator Light Circuit Malfunction (Aug 2005 – Dec 2005) →