INSTALLATION
Removal / installation · Vehicles built from Nov 2006
| 1. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY |
![]() ![]() |
Install the grommet onto the brake booster.
Install the vacuum check valve onto the brake booster.
| 2. INSTALL BRAKE BOOSTER |
Install a new gasket onto the brake booster.
Install the brake booster with the 4 nuts.

- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Install the wire harness clamp.
Connect the vacuum hose to the vacuum check valve with the clip.

Install the wire harness clamp bracket onto the cylinder head cover with the bolt.

- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
Connect the camshaft timing oil control valve connector.
Install the wire harness clamp bracket onto the cylinder head cover with the bolt.

- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
![]() ![]() |
Provisionally install the push rod clevis onto the brake booster.
- HINT:
- Tighten the push rod lock nut when adjusting the brake pedal height.
Apply lithium soap base glycol grease to the push rod pin.
Install the push rod clevis onto the brake pedal with the push rod pin and clip.
Install the return spring.
| 4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER |
![]() ![]() |
Install a new stop light switch mounting adjuster onto the pedal support.
| 5. INSTALL STOP LIGHT SWITCH |
![]() ![]() |
Insert the stop light switch into the adjuster until it just touches the brake pedal.
- NOTICE:
- Do not depress the brake pedal.
Make a quarter turn clockwise to install the stop light switch.

- NOTICE:
- Do not depress the brake pedal.
- HINT:
- The turning torque for installing the stop light switch:
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
Check the stop light switch clearance.
- Stop light switch clearance:
- 0.5 to 2.6 mm (0.020 to 0.102 in.)
Connect the connector to the stop light switch.
| 6. INSTALL INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY |
Engage the 4 claws and install the instrument panel under cover.

| 7. INSTALL BRAKE MASTER CYLINDER |
![]() ![]() |
Temporarily install the brake tube into the union and brake tube way.
Install a new O-ring onto the brake master cylinder.
Install the brake master cylinder onto the brake booster.
Temporarily install the union with brake tube and brake tube way into the brake master cylinder with 2 new gaskets and union bolt.

Install the vacuum check valve bracket.
Install the 2 nuts.
- Torque:
- 18 N*m{ 180 kgf*cm , 13 ft.*lbf }
Fully tighten the union bolt.

- Torque:
- 30 N*m{ 310 kgf*cm , 22 ft.*lbf }
Using SST, fully tighten the 2 brake tubes.

- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
Using SST, install the 2 brake tubes into the brake master cylinder.

- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
Connect the 4 wire harness clamps.

Connect the brake fluid level warning switch connector.
| 8. CONNECT CLUTCH RESERVOIR TUBE |
![]() ![]() |
Connect the reservoir tube with the clip.
| 9. INSTALL OUTER COWL TOP PANEL |
![]() ![]() |
Install the cowl top panel with the 9 bolts.
- Torque:
- 6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
Connect the wire harness clamp.

| 10. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2 |
![]() ![]() |
Engage the claw to install No. 2 cowl to register duct.
| 11. INSTALL FRONT WIPER MOTOR AND LINK |
![]() ![]() |
Connect the connector.
Slide the wiper link as shown in the illustration and engage the rubber pin with the body.
Install the front wiper motor and link with the 2 bolts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
| 12. INSTALL COWL TOP VENTILATOR LOUVER LH |
![]() ![]() |
Engage the 4 claws and install the cowl top ventilator louver LH.
Install the clip.
| 13. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() ![]() |
Engage the 10 claws and install the cowl top ventilator louver sub-assembly.
Install the clip.
Connect the washer hose.
| 14. INSTALL HOOD TO COWL TOP SEAL |
![]() ![]() |
Engage the 7 clips and install the hood to cowl top seal.
| 15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() ![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Align the blade tip with the mark on the windshield glass, as shown in the illustration.

Tighten the nut of the front wiper arm.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
| 17. INSTALL FRONT WIPER ARM HEAD CAP |
![]() ![]() |
Engage the claw and install the 2 front wiper arm head caps.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 19. FILL RESERVOIR WITH BRAKE FLUID |
![]() ![]() |
Disengage the 2 clips and separate the hood to cowl top seal.
Remove the cowl top ventilator louver.
Set the brake fluid can upside down onto the reservoir.

- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
| 20. BLEED MASTER CYLINDER |
- HINT:
- If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.
Using SST, disconnect the brake tubes from the master cylinder.

- SST
- 09023-00100
Slowly depress the brake pedal and hold it there (Step A).

Block the outer holes with your fingers, and release the brake pedal (Step B).

Repeat steps A and B 3 or 4 times.
Using SST, connect the brake tubes to the master cylinder.

- SST
- 09023-00100
- Torque:
- for use without SST:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
- for use with SST:
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf }
- HINT:
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
- This torque value is effective when SST is parallel to a torque wrench.
- Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
| 21. BLEED BRAKE LINE |
![]() ![]() |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).
At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).
Repeat steps C and D until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 22. BLEED BRAKE ACTUATOR |
- NOTICE:
- After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with an intelligent tester by following the procedure below.
Depress the brake pedal more than 20 times with the engine off.
Connect the intelligent tester to the DLC3, and turn the ignition switch on (IG).
- NOTICE:
- Do not start the engine.
Select AIR BLEEDING on the intelligent tester.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Bleed the air out of the brake line when Step 1: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).
Repeat steps E and F until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
- Torque:
- Front Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for each wheel to bleed the air out of the brake line.
Bleed the air out of the suction line when Step 2: Inhalation appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator to bleed the air using the intelligent tester (Step G).
- NOTICE:
- Release the brake pedal at this time.
- HINT:
- This operation stops automatically after 4 seconds.
Check if the operation has stopped by referring to the intelligent tester display (Step H).
Repeat step G and H until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty.
- Bleed the air by following the steps displayed on the the intelligent tester.
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (Step I).
Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).
- NOTICE:
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.
- During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
- HINT:
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
- When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.
- The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
Tighten the bleeder plug, then release the brake pedal (Step K).
Repeat steps I to K until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.
- NOTICE:
- Bleed the air by following the steps displayed on the intelligent tester.
- Make sure that the master cylinder reservoir tank does not become empty.
- Bleed the air by following the steps displayed on the intelligent tester.
Connect the vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step M).
Repeat steps L and M until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
- Torque:
- Front Brake:
- 8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
- Rear Brake:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure for the other wheels to bleed the air out of the brake line.
Make sure that the air bleeding is complete by referring to the intelligent tester display.
| 23. CHECK FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3
| 24. INSPECT FOR BRAKE FLUID LEAK |
| 25. INSPECT AND ADJUST BRAKE PEDAL |
w/ Instrument Panel Under Cover:
Remove the instrument panel under cover (Click here).
Inspect the brake pedal height.

- Pedal height from floor:
w/ ABS, w/ VSC
w/o ABS
107.3 to 117.3 mm
(4.224 to 4.618 in.)
107.8 to 117.8 mm
(4.244 to 4.638 in.)
Adjust the brake pedal height.
Disconnect the connector from the stop light switch.
Turn the stop light switch counterclockwise, and remove the stop light switch.
Loosen the push rod lock nut.
Adjust the pedal height by turning the pedal push rod.
- Pedal height from floor:
w/ ABS, w/ VSC
w/o ABS
107.3 to 117.3 mm
(4.224 to 4.618 in.)
107.8 to 117.8 mm
(4.244 to 4.638 in.)
Tighten the push rod lock nut.
- Torque:
- 26 N*m{ 265 kgf*cm , 19 ft.*lbf }
Insert the stop light switch into the adjuster until it just touches the brake pedal.

- NOTICE:
- Do not depress the brake pedal.
Make a quarter turn clockwise to install the stop light switch.

- NOTICE:
- Do not depress the brake pedal.
- HINT:
- The turning torque for installing the stop light switch:
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less
Check the stop light switch clearance.
- Stop light switch clearance:
- 0.5 to 2.6 mm (0.020 to 0.102 in.)
Connect the connector to the stop light switch.
Inspect the brake pedal free play.

Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.
Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.
- Pedal free play:
- 1.0 to 6.0 mm (0.039 to 0.236 in.)
Inspect the brake pedal reserve distance.

Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.
- Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):
- w/ ABS:
Rear Brake
LHD
RHD
Drum
More than 73 mm (2.87 in.)
More than 71 mm (2.80 in.)
Disc
More than 80 mm (3.15 in.)
More than 80 mm (3.15 in.)
- w/o ABS:
LHD
RHD
More than 70 mm (2.75 in.)
-
- w/ VSC:
LHD
RHD
More than 85 mm (3.35 in.)
More than 75 mm (2.95 in.)
- HINT:
- If incorrect, troubleshoot the brake system.
- Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.
- If incorrect, troubleshoot the brake system.
w/ Instrument Panel Under Cover:
Install the instrument panel under cover (Click here).














