2005-2008 Yaris · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Nov 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


10. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Disengage the claw and remove the No. 2 cowl to register duct sub-assembly.


11. REMOVE OUTER COWL TOP PANEL

A108438
  1. Disengage the wire harness clamp.

  1. A115392
    Remove the 9 bolts and remove the cowl top panel outer.


12. DISCONNECT CLUTCH RESERVOIR TUBE

C159547
  1. Slide the clip and disconnect the reservoir tube.


13. REMOVE BRAKE MASTER CYLINDER

NOTICE:
Remove the brake master cylinder after depressing the brake pedal several times and bleeding the vacuum pressure from inside the brake booster.

  1. C159548
    Disconnect the brake fluid level warning switch connector.

  1. Disconnect the 4 wire harness clamps.

  1. C159549E01
    Using SST, separate the 2 brake tubes from the brake master cylinder.
    SST
    09023-00100  

  1. C159550E01
    Using SST, loosen the 2 brake tubes.
    SST
    09023-00100  

  1. C159551
    Loosen the union bolt.

  1. C159552
    Remove the 2 nuts.

  1. Remove the vacuum check valve bracket.

  1. Remove the union bolt, 2 gaskets, union with brake tube and brake tube way.

  1. Remove the brake master cylinder from the brake booster.

  1. Remove the O-ring from the brake master cylinder.

  1. C159554
    Remove the brake tube from the union and brake tube way.


14. REMOVE INSTRUMENT PANEL NO. 1 UNDER COVER SUB-ASSEMBLY

  1. B114572
    Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.


15. REMOVE STOP LIGHT SWITCH

C107592
  1. Disconnect the connector from the stop light switch.

  1. Turn the stop light switch counterclockwise, and remove the stop light switch.


16. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

C107593
  1. Remove the stop light switch mounting adjuster from the pedal support.


17. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

C107594
  1. Remove the brake pedal return spring.

  1. Loosen the push rod lock nut.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.

  1. Remove the push rod clevis from the brake booster.


18. REMOVE BRAKE BOOSTER

C159558
  1. Remove the bolt and wire harness bracket from the cylinder head cover.

  1. C159559
    Remove the camshaft timing oil control valve connector.

  1. Remove the bolt and wire harness bracket from the cylinder head cover.

  1. C159560
    Slide the clip and disconnect the vacuum hose from the check valve.

  1. C107597
    Remove the wire harness clamp and 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.


19. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

C159561
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.

← COMPONENTS (from Nov 2006)INSTALLATION (from Nov 2006) →