2005-2008 Yaris · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jan 2006


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.


3. REMOVE FRONT WIPER ARM HEAD CAP

  1. E127832E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E127833
    Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH

  1. E127834E01
    Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.


7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E127835
    Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.

  1. E127836
    Disconnect the washer hoses.

  1. Disengage the 5 hooks.


9. REMOVE FRONT WIPER MOTOR AND LINK

  1. E127837
    Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


10. REMOVE FRONT AIR SHUTTER SEAL

A133324
  1. Disengage the 3 claws and remove the front air shutter seal.


11. REMOVE COWL TOP PANEL OUTER

A128446
  1. Disengage the wire harness clamp.

  1. A128447
    Remove the 2 bolts and remove the cowl top to cowl inner brace.

  1. A128448
    Remove the 8 bolts and remove the cowl top panel outer.


12. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C107585
  1. Slide the clip and disconnect the reservoir tube.


13. REMOVE BRAKE MASTER CYLINDER

NOTICE:
Remove the brake master cylinder after depressing the brake pedal several times and bleeding the vacuum pressure from inside the brake booster.

  1. Disconnect the brake fluid level warning switch connector.

  1. C107586E01
    Using SST, separate the 2 brake tubes from the brake master cylinder.
    SST
    09023-00100  

  1. C107587
    Remove the 2 nuts and remove the brake master cylinder.

  1. Remove the O-ring from the brake master cylinder.


14. REMOVE INSTRUMENT PANEL UNDER TRAY

B132341
  1. Disengage the 4 claws and open the instrument panel under tray.

  1. B132333
    Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.


15. REMOVE STOP LIGHT SWITCH

C107592
  1. Disconnect the connector from the stop light switch.

  1. Turn the stop light switch counterclockwise, and remove the stop light switch.


16. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

C107593
  1. Remove the stop light switch mounting adjuster from the pedal support.


17. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

C107594
  1. Remove the brake pedal return spring.

  1. Loosen the push rod lock nut.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.

  1. Remove the push rod clevis from the brake booster.


18. REMOVE BRAKE BOOSTER

C107595
  1. Slide the clip and disconnect the vacuum hose from the check valve.

  1. C107596
    Remove the bolt and separate the wire harness bracket.

  1. C107597
    Remove the wire harness clamp and 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.


19. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

C107598
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.

← COMPONENTS (from Jan 2006)INSTALLATION (from Jan 2006) →