2005-2008 Yaris · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY

C107598
  1. Install the grommet onto the brake booster.

  1. Install the vacuum check valve onto the brake booster.


2. INSTALL BRAKE BOOSTER
  1. Install a new gasket onto the brake booster.

  1. C107597
    Install the brake booster with the 4 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the wire harness clamp.

  1. C107596
    Install the wire harness bracket with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C107595
    Connect the vacuum hose to the vacuum check valve with the clip.


3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

C107594
  1. Provisionally install the push rod clevis onto the brake booster.

    HINT:
    Tighten the push rod lock nut when adjusting the brake pedal height.

  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Install the push rod clevis onto the brake pedal with the push rod pin and clip.

  1. Install the return spring.


4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

C107593
  1. Install a new stop light switch mounting adjuster onto the pedal support.


5. INSTALL STOP LIGHT SWITCH

F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.

  1. F049044E08
    Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the connector to the stop light switch.


6. INSTALL INSTRUMENT PANEL UNDER TRAY

B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B132390
    Engage the 4 claws and install the instrument panel under tray.


7. INSTALL BRAKE MASTER CYLINDER
  1. Install a new O-ring onto the brake master cylinder.

  1. C107587
    Install the brake master cylinder with the 2 nuts.

    Torque:
    18 N*m{ 180 kgf*cm , 13 ft.*lbf }

  1. C107586E01
    Using SST, install the 2 brake tubes onto the brake master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. Connect the brake fluid level warning switch connector.


8. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

C107585
  1. Connect the reservoir tube with the clip.


9. INSTALL COWL TOP PANEL OUTER

A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }

  1. A128447
    Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }

  1. A128446
    Connect the wire harness clamp.


10. INSTALL FRONT AIR SHUTTER SEAL

A133324
  1. Engage the 3 claws to install the front air shutter seal.


11. INSTALL FRONT WIPER MOTOR AND LINK

  1. E127840
    Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


12. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E127836
    Connect the washer hoses.

  1. Engage the 5 hooks.

  1. E127835
    Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.


13. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH

  1. E129651
    Engage the 3 claws and install the cowl side ventilator sub-assembly LH.


14. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E058837E10
    Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E129694E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


17. INSTALL FRONT WIPER ARM HEAD CAP

  1. E127841
    Engage the claw and install the 2 front wiper arm head caps.


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


19. FILL RESERVOIR WITH BRAKE FLUID

C133125E01
  1. Remove the cowl top No. 2 ventilator louver center.

  1. C133126E01
    Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


20. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C116910E01
    Using SST, disconnect the brake tubes from the master cylinder.
    SST
    09023-00100  

  1. C116911E01
    Slowly depress the brake pedal and hold it there (Step A).

  1. C116912E01
    Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.

  1. C116910E01
    Using SST, connect the brake tubes to the master cylinder.
    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


21. BLEED BRAKE LINE

C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


22. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4


23. CHECK FOR BRAKE FLUID LEAKAGE

24. INSPECT AND ADJUST BRAKE PEDAL
  1. Remove the instrument panel under tray (Click here).

  1. C116874E01
    Inspect the brake pedal height.

    Pedal height from floor:
    107.3 to 117.3 mm (4.224 to 4.618 in.)

    If the pedal height is incorrect, adjust it.

  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor:
      107.3 to 117.3 mm (4.224 to 4.618 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. F049043E01
      Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.

    7. F049044E08
      Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    8. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    9. Connect the connector to the stop light switch.

  1. F048932E01
    Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.

  1. R000934E02
    Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):

      LHD
      RHD
      w/ ABS
      More than 73 mm (2.87 in.)
      More than 71 mm (2.80 in.)
      w/o ABS
      More than 70 mm (2.75 in.)
      -

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.

  1. Install the instrument panel under tray (Click here).

← REMOVAL (from Jan 2006)COMPONENTS (from Nov 2006) →