2005-2008 Yaris · Service Manual BODY ELECTRICAL

DTC CHECK / CLEAR

Troubleshooting · Vehicles built from Aug 2005


CHECK DIAGNOSTIC CODE

  1. Entering diagnostic modes

    1. C138634E01
      C138635E01
      C115109E01
      C138621E01
      Turn off the audio system and turn the ignition switch on (ACC). While pressing preset switches 1 and 6 at the same time, press the DISC (DISC TAPE) switch 3 times.

      HINT:
      1. When the system enters a diagnostic mode, a beep sound is emitted 3 times and all the elements turn on during switch check mode.
      2. It takes about 40 seconds to complete the system check and the diagnostic memory check.
      3. All elements on the LCD illuminate.
      4. When pressing the switch, confirm that a beep sound is emitted.

  2. Service check mode

    1. Press the SEEK TRACK UP switch to enter service check mode.

    2. In service check mode, the system check and diagnostic memory check are performed, and the physical address (component code) check results are displayed in numerical order.

      Terms
      Definitions
      Physical address (component code)
      Three-digit code (in hexadecimal) given to each component of AVC-LAN. Individual symbol provided corresponding to each function.
      Logical address
      Two-digit code (in hexadecimal) given to each function and component unit in each component of AVC-LAN.
      Code No. (physical address) List 
      Code No. (physical address)
      Component Name
      190
      Radio receiver (audio head unit)

  3. Exiting diagnostic modes

    1. Press the DISC (DISC TAPE) switch for 2 seconds or more, or turn the ignition switch off.

  4. Service check mode result display (for checking the current and the past conditions of the system)

    1. Press the SEEK TRACK switch to see the check results of each component.
      I100978E06
      E110359E03

    2. Check result displays.

      Display
      Original Language
      Meaning
      Action to be Taken
      good
      Good (normal)
      No DTC detected in either "System Check Mode" or "Diagnostic Memory Check Mode".
      -
      nCon
      No connection
      System recognized component when it registered, but component gives no response to ''Diagnostic Mode ON Request''.
      Check power source circuit and communication circuit of component indicated by physical address (component code).
      ECHn
      Exchange
      One or more DTCs for ''Exchange'' detected in either ''System Check Mode'' or ''Diagnostic Memory Check Mode''.
      Go to detailed information mode to check trouble area in DTC list.
      CHEC
      Check
      When no DTCs detected for ''Exchange'', one or more DTCs for ''Check'' detected in either ''System Check Mode'' or ''Diagnostic Memory Check Mode''.
      Go to detailed information mode to check trouble area in DTC list.
      OLd
      Old version
      Old DTC application identified and DTC detected in either ''System Check Mode'' or ''Diagnostic Memory Check Mode''.
      -
      nrES
      No response
      Device gives no response to ''System Check Result Request'' or ''Diagnostic Memory Request''.
      Check power source circuit and communication circuit of component indicated by physical address (component code).

    3. To perform the service check again, press preset switch 1.

  5. Detailed information mode (when displaying DTCs of malfunctioning components)

    1. While "CHEC" or "ECHn" is displayed, press preset switch 2 to enter detailed information mode.

    2. Press the SEEK TRACK switch to display the "System Check Result (SYS)" and "Diagnostic Memory Check Result (CODE)".
      E106740E05
      E106741E06

    3. Displayed items in detailed information mode

      Division Code for DTC Display
      Meaning
      Sequential order of detailed information displayed when SEEK TRACK UP switch pressed (order reversed when SEEK TRACK DOWN switch pressed)
      SYS
      System check result display
      1. Logical address
      2. DTC
      CODE
      Diagnostic memory check result display
      1. Logical address
      2. DTC
      3. Sub-code
      4. Connection check number
      5. Number of times of occurrence

    4. Check the trouble area in the DTC list.

    5. To return to service check mode, press preset switch 3.


CLEAR DTC
  1. Clearing an individual DTC from the memory (when individually clearing the memories of DTCs detected in the past)

    1. Press preset switch 5 for 2 seconds or more while "ECHn" is displayed in service check mode or during detailed information mode.

      1. When a DTC memory has been cleared, only a physical address (component code) is displayed for the target component.
      2. To check DTCs, press preset switch 1 and perform the service check again.

  2. Clearing the entire DTC memory (when clearing the memory of all the DTCs detected in the past)

    1. Enter diagnostic modes after repairing the trouble area.

    2. Press preset switch 5 for 2 seconds or more ("CLR" is displayed at this time).

      HINT:
      1. A beep sound is emitted once when the entire DTC memory is completely cleared.
      2. When the DTC memories for all the components are cleared, only physical addresses (component codes) are displayed.

    3. Press preset switch 1 to perform the service check again, and check that no DTCs are displayed.

  3. Exiting diagnostic modes

    1. Press the DISC (DISC TAPE) switch for 2 seconds or more, or turn the ignition switch off.

← TERMINALS OF ECU (from Aug 2005)Noise Occurs (from Aug 2005) →