2005-2008 Yaris · Service Manual BODY

B2321 Driver Side Door ECU Communication Stop

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

DTC B2321 is output when the communication between the power window regulator motor (driver side) and main body ECU stops for more than 10 seconds.

NOTICE:
When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.

DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication from power window regulator motor (driver side) for more than 10 seconds
  1. Power window regulator motor (driver side)
  2. Main body ECU
  3. Wire harness

WIRING DIAGRAM

B123829E02

INSPECTION PROCEDURE


1. CHECK WHETHER DTC OUTPUT RECURS (DTC B2321)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear the DTCs.

  1. Select the following menu items: Body / Body ECU / DTC.

  1. Result DTCs.

    Display (DTC Output)
    Proceed To
    B2321
    A
    No DTC Output
    B



B
SYSTEM IS OK
A


2. READ VALUE OF INTELLIGENT TESTER (COMMUNICATION D DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body/ Body ECU/ Data List / Comm D-Door Mtr.

  1. Read the result displayed on the tester.

    Result:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Comm D-Door Mtr
    Connection status between power window regulator motor assembly (driver door) and main body ECU/
    OK/Stop
    OK: Connection
    Stop: No connection



OK
REPLACE MAIN BODY ECU
NG


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR (DRIVER SIDE))

  1. B129952E01
    Disconnect the F8 or G8 power window motor connector.

  1. Disconnect the D64 or D33 main body ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (w/ entry and start system):
    LHD 
    Tester Connection
    Specified Condition
    F8-9 (MPX2) - D64-23 (CANP)
    Below 1 Ω
    F8-9 (MPX2) or D64-23 (CANP) - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    G8-9 (MPX2) - D64-23 (CANP)
    Below 1 Ω
    G8-9 (MPX2) or D64-23 (CANP) - Body ground
    10 kΩ or higher


    Standard resistance (w/o entry and start system):
    LHD 
    Tester Connection
    Specified Condition
    F8-9 (MPX2) - D33-4 (CANP)
    Below 1 Ω
    F8-9 (MPX2) or D33-4 (CANP) - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    G8-9 (MPX2) - D33-4 (CANP)
    Below 1 Ω
    G8-9 (MPX2) or D33-4 (CANP) - Body ground
    10 kΩ or higher

  1. Reconnect the power window motor connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK WHETHER DTC OUTPUT RECURS (DTC B2321)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear the DTCs.

  1. Check whether DTC B2321 recurs 10 seconds or more after the ignition switch is turned on (IG).

    OK:
    No DTC is output.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
OK

REPLACE MAIN BODY ECU


← B2313 Glass Position Initialization Incomplete (from Aug 2005)B2325 LIN Communication Bus Malfunction (from Aug 2005) →