2005-2008 Yaris · Service Manual ENGINE

P0133 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Nov 2005

CAUTION / NOTICE / HINT

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P0130 (Click here).
DTC No.
DTC Detection Conditions
Trouble Areas
P0133
While idling with warm engine, response time for voltage output of Heated Oxygen (HO2) sensor to change from rich to lean or from lean to rich is 1 second or more (2 trip detection logic)
  1. Open or short in HO2 sensor (sensor 1) circuit
  2. HO2 sensor (sensor 1)
  3. HO2 sensor heater (sensor 1)
  4. Integration relay (EFI relay)
  5. Air induction system
  6. Fuel pressure
  7. Injector
  8. ECM

WIRING DIAGRAM

Refer to DTC P0130 (Click here).

CONFIRMATION DRIVING PATTERN

A128471E01

HINT:
This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

  1. (1) Connect the intelligent tester to the DLC3.
  2. (2) Turn the ignition switch on (IG) and turn the tester on.
  3. (3) Clear DTCs (Click here).
  4. (4) Switch the ECM from normal mode to check mode (Click here).
  5. (5) Start the engine.
  6. (6) Allow the engine to idle until the engine coolant temperature reaches 40°C (104°F).
  7. (7) Drive the vehicle at a vehicle speed of more than 40 km/h (25 mph) for 35 seconds or more.
  8. (8) Allow the engine to idle for 40 seconds or more.
  9. (9) Repeat steps (7) and (8) described above at least 3 times.
  10. (10) Allow the engine to idle for 40 seconds or more.

HINT:
The MIL is illuminated during step (10) if a malfunction still exists.

NOTICE:
If the conditions in this test are not strictly followed, malfunctions may not be detected.


INSPECTION PROCEDURE

HINT:
It is possible that the malfunctioning area can be found using the Active Test Control operation. The Active Test can determine if the heated oxygen sensor or other potential trouble areas are malfunctioning or not.
The injection volume can be switched to -12.5% (decrease) or +25% (increase) by the Active Test.
The Active Test procedure enables a technician to check and graph the voltage outputs of the heated oxygen sensors.

  1. Procedure:
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG).
    3. Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
    4. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Active Test while the engine is idling.

Standard:
The heated oxygen sensor reacts in accordance with the increases and decreases in injection volume:
+25% → RICH output: More than 0.5 V
-12.5% → LEAN output: Less than 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of 20 seconds.
If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and the DTCs are recorded.

Case
Heated Oxygen Sensor Voltage (sensor 1)
Heated Oxygen Sensor Voltage (sensor 2)
Main Suspected Trouble Area
1
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
-
Heated Oxygen Sensor Voltage
0.5 V or more
Below 0.4 V
A104056
Heated Oxygen Sensor Voltage
0.5 V or more
Below 0.4 V
A122588
2
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Heated oxygen sensor (sensor 1)
  2. Heated oxygen sensor heater (sensor 1)
Heated Oxygen Sensor Voltage
Almost
no reaction
A103185
Heated Oxygen Sensor Voltage
0.5 V or more
Below 0.4 V
A122588
3
Injection Volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Heated oxygen sensor (sensor 2)
  2. Heated oxygen sensor heater (sensor 2)
Heated Oxygen Sensor Voltage
0.5 V or more
Below 0.4 V
A104056
Heated Oxygen Sensor Voltage
Almost
no reaction
A103185
4
Injection volume
+25%
-12.5%
A103184
Injection Volume
+25%
-12.5%
A103184
  1. Injector fuel pressure, exhaust gas leak, etc.
    (air-fuel ratio is extremely LEAN or RICH)
Heated Oxygen Sensor Voltage
Almost
no reaction
A103185
Heated Oxygen Sensor Voltage
Almost
no reaction
A103185

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0133)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0133
    A
    P0133 and other DTCs
    B

    HINT:
    If any DTCs other than P0133 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. READ VALUE USING INTELLIGENT TESTER (HEATED OXYGEN SENSOR DURING IDLING)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1S1.

  1. Warm up the Heated Oxygen (HO2) sensor at an engine speed of 2,500 rpm for approximately 90 seconds.

  1. Read the voltage output of the front HO2 sensor displayed on the tester, while the engine is idling.

    Standard:
    Fluctuates between less than 0.35 V and more than 0.45 V, and period "t" is less than 1 second (refer to table below).

A128469E01


OK
Go to step 9
NG


3. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A115661E05
  1. Disconnect the C43 Heated Oxygen (HO2) sensor (sensor 1) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    HT1A (1) - +B (2)
    5 to 10 Ω at 20°C (68°F)
    HT1A (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK


4. INSPECT INTEGRATION RELAY (EFI FUSE AND EFI RELAY)
A107921E21
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse from the integration relay.

    2. Check the EFI fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI fuse.

  1. Inspect the EFI relay.

    1. Check the EFI relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


5. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A104950E07
A112568E06
  1. Disconnect the C43 HO2 sensor (sensor 1) connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    OX1A (C43-3) - OX1A (C20-112)
    Below 1 Ω
    HT1A (C43-1) - HT1A (C20-109)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    OX1A (C43-3) or OX1A (C20-112) - Body ground
    10 kΩ or higher
    HT1A (C43-1) or HT1A (C20-109) - Body ground

  1. Reconnect the HO2 sensor (sensor 1) connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8. INSPECT FUEL INJECTOR
  1. Check the injection volume (Click here).

    Standard:
    36 to 46 cm3 (2.2 to 2.8 cu in.) per 15 seconds



NG
REPLACE FUEL INJECTOR
OK

REPLACE HEATED OXYGEN SENSOR

9. PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs before performing the confirmation driving pattern.


NEXT


10. CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0133
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE HEATED OXYGEN SENSOR


← P0130 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1) (+ P2195, P2196) (from Nov 2005)P0134 Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1) (from Nov 2005) →