P0130 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built from Nov 2005
Also covers:
- P2195 Oxygen Sensor Signal Stuck Lean (Bank 1 Sensor 1)
- P2196 Oxygen Sensor Signal Stuck Rich (Bank 1 Sensor 1)
CAUTION / NOTICE / HINT
- HINT:
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
DESCRIPTION
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.The HO2 sensor is located in front of the TWC, and detects the oxygen concentration in the exhaust gas.
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor indicates to the ECM that the air-fuel ratio is lean (low voltage, i.e. less than 0.45 V). Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor indicates to the ECM that the air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.
The HO2 sensor is of the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.


- HINT:
- The ECM provides an ON/OFF control circuit to flow the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


| DTC No. |
DTC Detection Conditions |
Trouble Areas |
| P0130 |
Voltage output of oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm engine (2 trip detection logic) |
|
| P2195 |
Output voltage of HO2 sensor remains at 0.5 V or less during idling with warm engine (2 trip detection logic) |
|
| P2196 |
Output voltage of HO2 sensor remains at 0.4 V or more during idling with warm engine (2 trip detection logic) |
WIRING DIAGRAM


CONFIRMATION DRIVING PATTERN


- HINT:
- This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.
- (a) Connect an intelligent tester to the DLC3.
- (b) Turn the ignition switch on (IG) and turn the tester on.
- (c) Clear DTCs (Click here).
- (d) Switch the ECM from normal mode to check mode (Click here).
- (e) Start the engine.
- (f) Allow the engine to idle until the engine coolant temperature reaches 75°C (167°F).
- (g) Drive the vehicle at a vehicle speed of more than 40 km/h (25 mph) for 20 seconds or more.
- (h) Allow the engine to idle for 30 seconds or more.
- (i) Repeat steps (g) and (h) described above at least 3 times.
- (j) Allow the engine to idle for 40 seconds or more.
- HINT:
- The MIL is illuminated during step (f) if a malfunction still exists.
- NOTICE:
- If the conditions in this test are not strictly followed, malfunctions may not be detected.
INSPECTION PROCEDURE
- HINT:
- It is possible that the malfunctioning area can be found using the Active Test Control operation. The Active Test can determine if the heated oxygen sensor or other potential trouble areas are malfunctioning or not.
- The injection volume can be switched to -12.5% (decrease) or +25% (increase) by the Active Test.
- The Active Test procedure enables a technician to check and graph the voltage outputs of the heated oxygen sensors.
- Procedure:
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch on (IG).
- Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
- Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
- Perform the Active Test while the engine is idling.
- Standard:
- The heated oxygen sensor reacts in accordance with the increases and decreases in injection volume:
+25% → RICH output: More than 0.5 V
-12.5% → LEAN output: Less than 0.4 V
- NOTICE:
- The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of 20 seconds.
- If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and the DTCs are recorded.
| Case |
Heated Oxygen Sensor Voltage (sensor 1) |
Heated Oxygen Sensor Voltage (sensor 2) |
Main Suspected Trouble Area |
||
| 1 |
Injection Volume +25% -12.5% |
![]() ![]() |
Injection Volume +25% -12.5% |
![]() ![]() |
- |
| Heated Oxygen Sensor Voltage 0.5 V or more Below 0.4 V |
![]() ![]() |
Heated Oxygen Sensor Voltage 0.5 V or more Below 0.4 V |
![]() ![]() |
||
| 2 |
Injection Volume +25% -12.5% |
![]() ![]() |
Injection Volume +25% -12.5% |
![]() ![]() |
|
| Heated Oxygen Sensor Voltage Almost no reaction |
![]() ![]() |
Heated Oxygen Sensor Voltage 0.5 V or more Below 0.4 V |
![]() ![]() |
||
| 3 |
Injection Volume +25% -12.5% |
![]() ![]() |
Injection Volume +25% -12.5% |
![]() ![]() |
|
| Heated Oxygen Sensor Voltage 0.5 V or more Below 0.4 V |
![]() ![]() |
Heated Oxygen Sensor Voltage Almost no reaction |
![]() ![]() |
||
| 4 |
Injection volume +25% -12.5% |
![]() ![]() |
Injection Volume +25% -12.5% |
![]() ![]() |
|
| Heated Oxygen Sensor Voltage Almost no reaction |
![]() ![]() |
Heated Oxygen Sensor Voltage Almost no reaction |
![]() ![]() |
||
- HINT:
- Read freeze frame data using an intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0130, P2195 AND/OR P2196) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed To
P0130, P2195 and/or P2196
A
P0130, P2195 and/or P2196 and other DTCs
B
- HINT:
- If any DTCs other than P0130, P2195 and/or P2196 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1)) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1 S1.
Allow the engine to run for 90 seconds at 2,500 rpm.
Read the heated oxygen sensor voltage while the engine is idling.
- OK:
- The heated oxygen sensor voltage alternates between below 0.4 V and more than 0.5 V (see the following table).


|
|
||||
| NG | |
| 3. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the C43 Heated Oxygen (HO2) sensor (sensor 1) connector.
Measure the resistance.
- Standard resistance:
Tester Connections
Specified Conditions
HT1A (1) - +B (2)
5 to 10 Ω at 20°C (68°F)
HT1A (1) - E2 (4)
10 kΩ or higher
Reconnect the HO2 sensor connector.
|
|
||||
| OK | |
| 4. INSPECT INTEGRATION RELAY (EFI FUSE AND EFI RELAY) |
![]() ![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse.
Remove the EFI fuse from the integration relay.
Check the EFI fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI fuse.
Inspect the EFI relay.
Check the EFI relay resistance.
- Standard resistance:
Tester Connections
Specified Conditions
1C-1 - 1A-4
10 kΩ or higher
Below 1 Ω
(Apply battery voltage between terminals 1A-2 and 1A-3)
Reinstall the integration relay.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM) |
![]() ![]() ![]() ![]() |
Disconnect the C43 HO2 sensor (sensor 1) connector.
Disconnect the C20 ECM connector.
Check the resistance.
- Standard resistance (Check for open):
Tester Connections
Specified Conditions
OX1A (C43-3) - OX1A (C20-112)
Below 1 Ω
HT1A (C43-1) - HT1A (C20-109)
- Standard resistance (Check for short):
Tester Connections
Specified Conditions
OX1A (C43-3) or OX1A (C20-112) - Body ground
10 kΩ or higher
HT1A (C43-1) or HT1A (C20-109) - Body ground
Reconnect the HO2 sensor (sensor 1) connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks.
- OK:
- No leakage from air induction system.
|
|
||||
| OK | |
| 7. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 8. INSPECT FUEL INJECTOR |
Check the injection volume (Click here).
- Standard:
- 36 to 46 cm3 (2.2 to 2.8 cu in.) per 15 seconds
|
|
||||
| OK | ||
| ||
| 9. PERFORM CONFIRMATION DRIVING PATTERN |
- HINT:
- Clear all DTCs before performing the confirmation driving pattern.
| NEXT | |
| 10. CHECK WHETHER DTC OUTPUT RECURS (DTC P0130, P2195 AND/OR P2196) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed To
P0130, P2195 and/or P2196
A
No output
B
|
|
||||
| A | ||
| ||







