2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Disengage the 4 pins and remove engine cover No. 1.


3. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A118837
  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps, and separate the wire harness from the air cleaner cap.

  1. A118856
    Unfasten the 2 lock clamps, and separate the air cleaner cap.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the air cleaner hose from the turbocharger, and remove the air cleaner with hose.


4. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

A118839
  1. Remove the air cleaner filter element from the air cleaner.


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }


6. REMOVE EXHAUST PIPE ASSEMBLY FRONT

A118855
  1. Remove the 2 bolts and 2 compression springs, and separate the exhaust pipe front from the exhaust manifold converter.

  1. Remove the bolt and clamp, and separate the exhaust pipe front from the exhaust pipe rear.

  1. Disengage the 3 exhaust pipe supports, and remove the exhaust pipe front.

  1. Remove the gasket from the exhaust pipe front.

  1. A098223
    Remove the gasket from the exhaust manifold converter.


7. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


10. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


12. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


14. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


15. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


16. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A118801E01
  1. Disengage the claws, and remove cowl top register duct No. 2.


17. REMOVE COWL TOP PANEL OUTER

A126332
  1. Separate the wire harness.

  1. Remove the 9 bolts and cowl top panel outer.


18. REMOVE TURBO INSULATOR NO. 1

A118858E01
  1. For LHD:

    1. Remove the 2 bolts, and separate the brake booster vacuum pipe.

  1. A118857E01
    For RHD:

    1. Remove the bolt, and separate the brake booster vacuum pipe.

  1. A098282
    Remove the 3 bolts and turbo insulator No. 1.


19. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

A126329
  1. Remove the bolt, and separate the manifold support bracket.

  1. Remove the 3 nuts and exhaust manifold converter.

  1. A098284
    Remove the gasket from the turbocharger.


20. REMOVE TURBO OIL INLET PIPE

A098287
  1. Remove the wire harness clamp.

  1. Remove the bolt.

  1. Remove the 2 union bolts, oil inlet pipe and 4 gaskets.


21. REMOVE AIR HOSE NO. 1

A098288
  1. Loosen the 2 hose clamp bolts and remove intercooler air hose No. 1.


22. REMOVE TURBOCHARGER SUB-ASSEMBLY

G038744
  1. Remove the 2 nuts.

  1. A098289
    Disconnect the vacuum hose from the turbocharger.

  1. Remove the 3 nuts and turbocharger.

  1. A098290
    Remove the gasket from the exhaust manifold.

  1. G038742
    Remove the gasket from the turbocharger.


23. REMOVE TURBO OIL OUTLET PIPE

G038743
  1. Remove the 2 nuts and turbo oil outlet pipe.

  1. G038745
    Remove the gasket from the cylinder block.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →