2005-2008 Yaris · Service Manual BODY ELECTRICAL

Light Control Switch Circuit

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

This circuit detects the state of the headlight dimmer switch.

WIRING DIAGRAM

B136789E01

INSPECTION PROCEDURE


1. INSPECT VEHICLE SPECIFICATIONS
  1. Check whether the vehicle is equipped with the daytime running light system.

    Result:
    Daytime running light system
    Proceed to
    No
    A
    Yes
    B



B
Go to step 3
A


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH)
B135320E01
  1. Disconnect the 4M, 4E and 4J main body ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    4M-4 - 4E-12
    Light control switch OFF → HEAD
    10 kΩ or higher → Below 1 Ω
    4E-10 - 4E-12
    Light control switch OFF → HEAD
    10 kΩ or higher → Below 1 Ω
    4J-4 - 4E-12
    Light control switch OFF → HEAD
    Headlight dimmer switch LOW → HIGH
    10 kΩ or higher → Below 1 Ω
    4J-4 - 4E-12
    Light control switch OFF → HEAD
    Headlight dimmer switch LOW → FLASH
    10 kΩ or higher → Below 1 Ω
    4J-3 - 4E-12
    Light control switch OFF → HEAD
    Headlight dimmer switch LOW
    10 kΩ or higher → Below 1 Ω

  1. Reconnect the main body ECU connectors.



NG
Go to step 4
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DIMMER SWITCH, DRL RELAY - DIMMER SWITCH)

  1. B135321E01
    Disconnect the 4M and 4E main body ECU connectors.

  1. Disconnect the D50 running light relay assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    4M-4 - Body ground
    Light control switch OFF → HEAD
    10 kΩ or higher → Below 1 Ω
    4E-10 - Body ground
    Light control switch OFF → HEAD
    10 kΩ or higher → Below 1 Ω
    D50-6 (HF) - Body ground
    Light control switch OFF → HEAD
    Headlight dimmer switch LOW → HIGH or FLASH
    10 kΩ or higher → Below 1 Ω
    D50-13 (HI) - Body ground
    Light control switch OFF → HEAD
    Headlight dimmer switch LOW → HIGH or FLASH
    10 kΩ or higher → Below 1 Ω
    D50-4 (H) - Body ground
    Headlight Dimmer switch LOW → HEAD
    10 kΩ or higher → Below 1 Ω

  1. Reconnect the main body ECU connectors.

  1. Reconnect the from running light relay assembly connector.



NG
Go to step 4
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

4. INSPECT HEADLIGHT DIMMER SWITCH

  1. B126089E09
    Inspect the light control switch.
    1. Measure the resistance.

      Standard resistance:
      LHD and RHD for Europe:
      Tester connection
      Condition
      Specified condition
      10 (T1) - 13 (B1)
      11 (ED) - 12 (RF)
      OFF
      10 kΩ or higher
      10 (T1) - 13 (B1)
      TAIL, HEAD
      Below 1 Ω
      11 (ED) - 12 (RF)
      HEAD
      Below 1 Ω
      RHD except Europe:
      Tester connection
      Condition
      Specified condition
      5 (B1) - 8 (T1)
      6 (RF) - 7 (ED)
      OFF
      10 kΩ or higher
      5 (B1) - 8 (T1)
      TAIL, HEAD
      Below 1 Ω
      6 (RF) - 7 (ED)
      HEAD
      Below 1 Ω

  1. Inspect the headlight dimmer switch.

    1. Measure the resistance.

      Standard resistance:
      LHD and RHD for Europe:
      Tester connection
      Condition
      Specified condition
      9 (HU) - 11 (ED)
      FLASH
      Below 1 Ω
      8 (HL) - 11 (ED)
      LOW BEAM
      Below 1 Ω
      9 (HU) - 11 (ED)
      HI BEAM
      Below 1 Ω
      RHD except Europe:
      Tester connection
      Condition
      Specified condition
      9 (HU) - 7 (ED)
      FLASH
      Below 1 Ω
      10 (HL) - 7 (ED)
      LOW BEAM
      Below 1 Ω
      9 (HU) - 7 (ED)
      HI BEAM
      Below 1 Ω

  1. Inspect the turn signal switch.

    1. Measure the resistance.

      Standard resistance:
      LHD and RHD for Europe:
      Tester connection
      Condition
      Specified condition
      5 (TL) - 7 (E)
      6 (TR) - 7 (E)
      OFF
      10 kΩ or higher
      5 (TL) - 7 (E)
      Left
      Below 1 Ω
      6 (TR) - 7 (E)
      Right
      Below 1 Ω
      RHD except Europe:
      Tester connection
      Condition
      Specified condition
      11 (E) - 12 (TL)
      11 (E) - 13 (TR)
      OFF
      10 kΩ or higher
      11 (E) - 12 (TL)
      Right
      Below 1 Ω
      11 (E) - 13 (TR)
      Left
      Below 1 Ω

  1. Inspect the fog light switch.

    1. Measure the resistance.

      Standard resistance:
      LHD and RHD for Europe:
      Tester connection
      Condition
      Specified condition
      3 (BFG) - 4 (LFG)
      2 (B) - 4 (LFG)
      OFF
      10 kΩ or higher
      3 (BFG) - 4 (LFG)
      Fog light switch ON
      Below 1 Ω
      2 (B) - 4 (LFG)
      Fog light switch ON
      Below 1 Ω
      RHD except Europe:
      Tester connection
      Condition
      Specified condition
      1 (LFG) - 2 (BFG)
      1 (LFG) - 3 (B)
      OFF
      10 kΩ or higher
      1 (LFG) - 2 (BFG)
      Fog light switch ON
      Below 1 Ω
      1 (LFG) - 3 (B)
      Fog light switch ON
      Below 1 Ω



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Back-up Light Circuit (from Nov 2006)Headlight Signal Circuit (from Aug 2005) →