2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. REMOVE FRONT WHEEL RH

2. DRAIN ENGINE OIL

3. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A125680
    Loosen the radiator drain cock plug.

  1. Remove the reserve tank cap and drain the coolant.

  1. Tighten the radiator drain cock plug.

    A128304E01


4. REMOVE ENGINE UNDER COVER
  1. Remove the 5 bolts, 4 screws and 2 clips and remove the engine under cover.


5. REMOVE BATTERY

6. REMOVE BATTERY TRAY

7. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


10. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


12. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


14. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


15. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


16. REMOVE COWL TO REGISTER DUCT SUB ASSEMBLY NO. 2

A118801E01
  1. Disengage the claws, and remove cowl top register duct No. 2.


17. REMOVE COWL TOP PANEL OUTER

A126332
  1. Separate the wire harness.

  1. Remove the 9 bolts and cowl top panel outer.


18. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

  1. A125743
    Disengage the 4 pins and remove engine cover No. 1.


19. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A118837
  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps, and separate the wire harness from the air cleaner cap.

  1. A118856
    Unfasten the 2 lock clamps, and separate the air cleaner cap.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the air cleaner hose from the turbocharger, and remove the air cleaner with hose.


20. REMOVE GLOW PLUG NO.1 CONNECTOR

  1. A098269
    Remove the 5 screw grommets.

  1. A098270
    Remove the nut and disconnect the glow terminal.

  1. Remove the 4 nuts and glow plug connector No. 1.


21. REMOVE EGR COOLER PIPE ASSEMBLY

  1. A125674
    Disconnect the 2 water by-pass hoses.

  1. Remove the bolt and 4 nuts, then remove the EGR cooler assembly.

  1. Remove the 2 gaskets.


22. REMOVE VACUUM REGULATING VALVE ASSEMBLY

A125788E01
  1. Disconnect the connector clamp and connector.

  1. Disengage the 2 hose clamps and disconnect the 2 vacuum hoses.

  1. Remove the 3 bolts, then remove the vacuum regulating valve together with the bracket.


23. REMOVE EGR VALVE ASSEMBLY

  1. A125675
    Disconnect the EGR valve connector and hose.

  1. Remove the 2 nuts, then remove the EGR valve assembly.

  1. Remove the gasket.


24. REMOVE DIESEL THROTTLE BODY ASSEMBLY

25. REMOVE INTAKE AIR CONNECTOR

  1. G036729
    Disconnect the vacuum hose shown in the illustration.

  1. Remove the 4 bolts, then remove the intake air connector.


26. REMOVE EGR PIPE CONNECTOR

  1. A128827
    Remove the 3 bolts, then remove the EGR pipe connector.


27. REMOVE INJECTION PIPE CLAMP NO.1

A098451
  1. Remove the 2 nuts, then remove injection pipe clamp No. 1.


28. REMOVE INJECTION PIPE CLAMP NO.2

A098452
  1. Remove the nut, then remove injection pipe clamp No. 2.


29. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 1

A069347E01
  1. Using a spanner (13 mm), hold the injector steadily, and using SST, remove the injection pipe from the injector side.

    SST
    09023-38401  

  1. Using SST, remove the injection pipe from the common rail side.

    SST
    09023-38401  

  1. After removing the injection pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


30. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 2
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


31. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 3
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


32. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 4
  1. Perform the same procedure as for injection pipe No. 1.

    SST
    09023-38401  


33. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

A098453
  1. Remove the 5 retainer springs, then remove the nozzle leakage pipe.


34. REMOVE INJECTOR ASSEMBLY

A098454E01

HINT:
  1. Each injector assembly has its own fuel injection part number. when replacing the injector assembly, store them in the correct order so that they can be returned to their original locations when reassembled.
  2. Arrange the injectors, clamps, washers, bolts and clamp seats in the correct order.

  1. Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 nozzle holder clamp seats.

  1. Disconnect the 4 injector connectors.

  1. Remove the 4 injectors from the cylinder head.

  1. Remove the 4 injection nozzle seats from the injector or cylinder head.

    NOTICE:
    When removing the injector, check that the injector nozzle seat is either attached to the injector, or remains in the cylinder head.


35. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

A098482E01
  1. Using a spanner (17 mm), hold the supply pump steady, and using SST, remove the fuel inlet pipe from the supply pump side.

    SST
    09023-38401  

  1. A098483E01
    Using SST, remove the fuel inlet pipe from the common rail side.
    SST
    09023-38401  

  1. After removing the fuel inlet pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


36. REMOVE COMMON RAIL ASSEMBLY

A098485
SST
09023-38401  
  1. Disconnect the 2 connectors.

  1. Disconnect the fuel hose.

  1. Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure sensor or fuel pressure regulator.


37. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

A125787
  1. Disconnect the 3 fuel hoses.

  1. Disconnect the 2 connectors.

  1. Remove the 3 bolts, then remove the supply pump.

  1. Remove the supply pump driving coupling.

  1. Remove the O-ring.

    NOTICE:
    When removing the supply pump, make sure that the drive coupling does not fall off, as it can be easily removed. If the drive coupling falls off, replace it with a new one.


38. REMOVE EXHAUST PIPE ASSEMBLY FRONT

A118855
  1. Remove the 2 bolts and 2 compression springs, and separate the exhaust pipe front from the exhaust manifold converter.

  1. Remove the bolt and clamp, and separate the exhaust pipe front from the exhaust pipe rear.

  1. Disengage the 3 exhaust pipe supports, and remove the exhaust pipe front.

  1. Remove the gasket from the exhaust pipe front.

  1. A098223
    Remove the gasket from the exhaust manifold converter.


39. REMOVE TURBO INSULATOR NO. 1

A118858E01
  1. For LHD:

    1. Remove the 2 bolts, and separate the brake booster vacuum pipe.

  1. A118857E01
    For RHD:

    1. Remove the bolt, and separate the brake booster vacuum pipe.

  1. A098282
    Remove the 3 bolts and turbo insulator No. 1.


40. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

A126329
  1. Remove the bolt, and separate the manifold support bracket.

  1. Remove the 3 nuts and exhaust manifold converter.

  1. A098284
    Remove the gasket from the turbocharger.


41. REMOVE TURBO OIL INLET PIPE

A098287
  1. Remove the wire harness clamp.

  1. Remove the bolt.

  1. Remove the 2 union bolts, oil inlet pipe and 4 gaskets.


42. REMOVE AIR HOSE NO.1

A098288
  1. Loosen the 2 hose clamp bolts and remove intercooler air hose No. 1.


43. REMOVE TURBO CHARGER SUB-ASSEMBLY

G038744
  1. Remove the 2 nuts.

  1. A098289
    Disconnect the vacuum hose from the turbocharger.

  1. Remove the 3 nuts and turbocharger.

  1. A098290
    Remove the gasket from the exhaust manifold.

  1. G038742
    Remove the gasket from the turbocharger.


44. REMOVE TURBO OIL OUTLET PIPE

G038743
  1. Remove the 2 nuts and turbo oil outlet pipe.

  1. G038745
    Remove the gasket from the cylinder block.


45. REMOVE EXHAUST MANIFOLD
  1. Remove the 2 bolts, then remove the manifold stay.

  1. A128801
    Remove the 2 bolts, then remove exhaust manifold heat insulator No. 1.

  1. A128802
    Remove the 5 nuts, then remove the exhaust manifold with turbocharger.


46. REMOVE FAN AND GENERATOR V BELT

A125681
  1. Remove the 3 bolts and clip, then separate the wire harness.

  1. A098654E01
    Loosen bolts A and B.

  1. Remove the fan and generator V belt.


47. REMOVE GENERATOR ASSEMBLY

A128374
  1. Remove the terminal cap.

  1. Separate the connector and harness clamp.

  1. Remove the nut and remove terminal B.

  1. A128375E01
    Remove fan belt adjusting slider fixing bolt A and nut B and remove the fan belt adjusting slider.

  1. A128376E01
    Remove fixing bolt C and remove the generator.


48. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

  1. A125730
    Support the engine with a jack and a wooden block, as shown in the illustration.

  1. A125676
    Remove the 7 bolts and nut, then remove the engine mounting insulator RH.


49. REMOVE WATER PUMP PULLEY

  1. A099104E01
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts, then remove the water pump pulley.


50. REMOVE WATER PUMP ASSEMBLY

  1. A099105
    Remove the 3 bolts and 2 nuts, then remove the water pump.


51. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

G036386
  1. Disconnect the injector connectors.

  1. A125690
    Disconnect the supply pump connector.

  1. A125682
    Disengage the wire harness clamps shown in the illustration.

  1. G036389
    Disconnect the VSV connector shown in the illustration, and disengage the wire harness clamp shown in the illustration.

  1. G036390
    Remove the screw grommet and nut, then separate the wire harness.

  1. Disconnect the common rail connector.

  1. G036391
    Remove the 3 bolts and the wire harness clamp shown in the illustration and disconnect the engine wire harness.

  1. A125691
    Disconnect the hose shown in the illustration.

  1. A125688
    Disconnect the hose shown in the illustration.

  1. A125692
    Disconnect the 3 vacuum hoses shown in the illustration.

  1. A125693
    Disconnect the vacuum hose shown in the illustration.

  1. A125689
    Disconnect the ventilation hose from the cylinder head.

  1. A125694
    Remove the 2 bolts, then remove the connector to vacuum reservoir tube.

  1. A128835
    Remove the 12 bolts, then remove the cylinder head cover.


52. REMOVE VACUUM PUMP ASSEMBLY

C129748
  1. Slide the clip and disconnect the vacuum hose.

  1. Disconnect the cam position sensor connector.

  1. C129749
    Remove the 2 bolts and vacuum pump.

  1. F048854
    Remove the 2 O-rings from the vacuum pump.


53. SET NO. 1 CYLINDER TO TDC/COMPRESSION

A125844E01
  1. Set the No. 1 cylinder to TDC/Compression.

    1. Turn the crankshaft pulley until the grooves of the crankshaft damper and oil pump are aligned.

    2. Check that the timing mark of the camshaft timing sprocket and the straight pin hole in the camshaft timing sprocket are in the positions shown in the illustration.

      HINT:
      If not, turn the crankshaft damper 1 revolution (360°) to align them as above.


54. REMOVE CRANK SHAFT DAMPER SUB-ASSEMBLY

  1. A099115E03
    Using SST, hold the crankshaft damper and loosen the crankshaft bolt.
    SST
    09960-10010   (09962-01000, 09963-01000)


55. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

  1. A125792
    Remove the 4 bolts, then remove the engine mounting bracket.


56. REMOVE TIMING CHAIN COVER NO.2

  1. A069329
    Remove the 2 bolts, then remove the timing cover No. 2.


57. REMOVE OIL PUMP ASSEMBLY

  1. A099117
    Remove the 16 bolts and nut.

  1. A099118
    Using a screwdriver with its tip wrapped in tape, remove the oil pump by prying out between the cylinder head and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pump assembly, cylinder head and cylinder block.

  1. A099119
    Remove the 2 O-rings from the cylinder block and oil pan.


58. REMOVE OIL PUMP SEAL

  1. A099121
    Using a screwdriver with its tip wrapped in tape, remove the oil pump seal.


59. REMOVE CHAIN TENSIONER ASSEMBLY NO. 1

A125803E01

NOTICE:
Do not rotate the crankshaft without the chain tensioner.

  1. Pull up the stopper plate to unlock the plunger.

  1. Push in the plunger to the end with the plunger unlocked.

  1. A125804E01
    Pull down the stopper plate with the plunger pushed to the end to lock the plunger.

  1. A087621
    Insert a 2.5 mm (0.095 in.) diameter bar into the hole in the stopper plate with the plunger locked.

    HINT:
    If the stopper plate is not completely pulled down and a 2.5 mm (0.098 in.) diameter bar cannot be inserted, unlock and pull out the plunger slightly. The stopper plate can then be completely pulled down and a 2.5 mm (0.098 in.) diameter bar can be inserted easily.

  1. A099122
    Remove the 2 bolts and chain tensioner No. 1.


60. REMOVE CHAIN TENSIONER SLIPPER

  1. A099123
    Remove the chain tensioner slipper from the cylinder block.


61. REMOVE CHAIN VIBRATION DAMPER NO.1

  1. A099124
    Remove the 2 bolts and chain vibration damper.


62. REMOVE CHAIN SUB-ASSEMBLY

  1. G035809E01
    Using SST, hold the camshaft timing sprocket.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 3 bolts, then remove the camshaft timing sprocket.

  1. G035810
    Remove the camshaft timing sprocket, crankshaft timing sprocket and chain together.


63. REMOVE CAMSHAFT

  1. G035811E03
    Remove the 10 bolts of the camshaft bearing caps in the sequence shown in the illustration, and then remove the 5 camshaft bearing caps.

    NOTICE:
    1. Using several steps, uniformly loosen the bolts while keeping the camshaft level.
    2. Do not remove camshaft beating cap No. 3.


64. REMOVE VALVE ROCKER ARM SUB-ASSEMBLY NO. 1

  1. G035812
    Remove the 8 valve rocker arms from the cylinder head.


65. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gage from the oil level gage guide.

  1. Remove the bolt, then remove the oil level gage guide.


66. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A125777
    Disconnect the vacuum hose shown in the illustration.

  1. A128788
    Disconnect the radiator inlet hose and the heater water hose.

  1. Remove the water temperature sensor.

    SST
    09817-33190  

  1. A128789
    Remove the bolt, then separate the water by-pass pipe.

  1. Disconnect each connector and wire harness from the cylinder head.

  1. A125806E01
    Using several steps, loosen the 10 bolts in the sequence shown in the illustration, and then remove the bolts and washers.

    NOTICE:
    1. When removing the bolts, do not drop the washer into the engine.
    2. Removing the cylinder head bolts in the wrong order may cause damage to the cylinder head.


67. REMOVE CYLINDER HEAD GASKET
← COMPONENTS (from Nov 2005)DISASSEMBLY (from Nov 2005) →