2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. REMOVE FRONT WHEELS

2. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A125680
    Loosen the radiator drain cock plug.

  1. Remove the reserve tank cap and drain the coolant.

  1. Tighten the radiator drain cock plug.

    A128304E01


3. REMOVE ENGINE UNDER COVER
  1. Remove the 5 bolts, 4 screws and 2 clips and remove the engine under cover.


4. DRAIN MANUAL TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


5. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


8. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY LH (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


13. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


14. REMOVE COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

A118801E01
  1. Disengage the claws, and remove cowl top register duct No. 2.


15. REMOVE COWL TOP PANEL OUTER

A126332
  1. Separate the wire harness.

  1. Remove the 9 bolts and cowl top panel outer.


16. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

  1. A125743
    Disengage the 4 pins and remove engine cover No. 1.


17. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A118837
  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps, and separate the wire harness from the air cleaner cap.

  1. A118856
    Unfasten the 2 lock clamps, and separate the air cleaner cap.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the air cleaner hose from the turbocharger, and remove the air cleaner with hose.


18. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

A118839
  1. Remove the air cleaner filter element from the air cleaner.


19. REMOVE AIR CLEANER CASE SUB-ASSEMBLY WITH AIR CLEANER INLET

  1. A125745
    Remove the 3 bolts, then remove the air cleaner case with air the cleaner inlet.


20. REMOVE AIR CLEANER BRACKET

  1. A125746
    Remove the 3 bolts, then remove the air cleaner No. 1 bracket.


21. REMOVE BATTERY

22. REMOVE BATTERY TRAY

23. REMOVE BATTERY CARRIER ASSEMBLY WITH WIRING HARNESS CLAMP

  1. C106370
    Remove the 5 bolts and the clip, then remove the battery carrier with the harness clamp.


24. REMOVE FAN AND GENERATOR V BELT

A125681
  1. Remove the 3 bolts and clip, then separate the wire harness.

  1. A098654E01
    Loosen bolts A and B.

  1. Remove the fan and generator V belt.


25. REMOVE WITH PULLEY COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

I102261E01
  1. Remove the compressor and pulley (Previous Version).

    1. Disconnect the connector and the clamp.

    2. Remove the 4 bolts and the compressor.

  1. I103531E02
    Remove the compressor and pulley (New Version).

    1. Disconnect the connector and the clamp.

    2. Remove the 2 nuts and 2 bolts.

    3. I103532E01
      Using "TORX" socket wrench E8, remove the 2 stud bolts and the compressor.


26. DISCONNECT AIR HOSE NO. 3

  1. A125663
    Loosen 2 hose clamps, then remove air hose No. 3.


27. DISCONNECT AIR HOSE NO. 2

  1. A125749
    Loosen hose clamp, then remove air hose No. 2.


28. REMOVE AIR TUBE NO. 1

C127619
  1. Loosen the hose clamp and disconnect air hose No. 1.

  1. Remove the bolt and separate the wire harness bracket.

  1. Remove the 2 bolts and remove air tube No. 1.


29. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

C115305
  1. Remove the 2 clips and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.


30. DISCONNECT VACUUM TRANSMITTING HOSE ASSEMBLY NO. 1

A125797

31. DISCONNECT TURBO PRESSURE HOSE

A125777

32. DISCONNECT UNION TO CONNECTOR TUBE HOSE

  1. A125691
    Disconnect the union to connector tube hose.


33. DISCONNECT FUEL HOSE NO. 1

  1. A125740E01
    Disconnect fuel hose No. 1 from the supply pump.


34. DISCONNECT FUEL HOSE NO. 2

  1. A125740E02
    Disconnect fuel hose No. 2 from the supply pump.


35. DISCONNECT RADIATOR HOSE NO. 2

  1. A125750
    Disconnect radiator hose No. 2 from the radiator.


36. DISCONNECT RADIATOR HOSE NO. 1

  1. A125748
    Disconnect radiator hose No. 1 from the cylinder head.


37. DISCONNECT WATER BY-PASS HOSE NO. 5

  1. A128832
    Disconnect water by-pass hose No. 5 from the reserve tank.


38. DISCONNECT HEATER INLET WATER HOSE

A125751

39. DISCONNECT HEATER OUTLET WATER HOSE

A125747

40. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

C115310
  1. Remove the 2 bolts and the clutch release cylinder.


41. REMOVE CLUTCH ACCUMULATOR ASSEMBLY (for Manual Transaxle)

  1. C127602
    Using SST, disconnect the release cylinder to accumulator tube.
    SST
    09023-00101  

  1. C127603
    Using SST, remove the accumulator to flexible hose tube.
    SST
    09023-00101  

  1. C127604
    Remove the bolt, then separate the flexible hose bracket.

  1. C127605
    Remove the 2 bolts and nut and remove the clutch accumulator.


42. DISCONNECT ENGINE WIRE
  1. Disconnect the engine wire harness from the ECM junction block.

  1. Pull the engine wire harness, disconnected from the ECM and junction block, out toward the engine room.

  1. Disconnect the engine wire from the engine room.


43. REMOVE COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Remove the 2 clips and the column hole cover silencer sheet.


44. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

A116500
  1. Hold the steering wheel with the seatbelt to avoid steering wheel rotation and damage to the spiral cable.

  1. A118670E01
    Put a matchmark on the sliding yoke and the intermediate shaft.

  1. Loosen the 2 bolts to separate the sliding yoke.


45. REMOVE EXHAUST PIPE ASSEMBLY FRONT

A118855
  1. Remove the 2 bolts and 2 compression springs, and separate the exhaust pipe front from the exhaust manifold converter.

  1. Remove the bolt and clamp, and separate the exhaust pipe front from the exhaust pipe rear.

  1. Disengage the 3 exhaust pipe supports, and remove the exhaust pipe front.

  1. Remove the gasket from the exhaust pipe front.

  1. A098223
    Remove the gasket from the exhaust manifold converter.


46. REMOVE FRONT AXLE SHAFT LH NUT

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


47. REMOVE FRONT AXLE HUB RH NUT

HINT:
Perform the same procedure as above on the opposite side.


48. SEPARATE FRONT SPEED SENSOR

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


49. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


50. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as above on the opposite side.


51. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


52. SEPARATE TIE ROD END SUB ASSEMBLY RH

HINT:
Perform the same procedure as above on the opposite side.


53. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO.1 LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


54. SEPARATE FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER NO. 1 RH

HINT:
Perform the same procedure as above on the opposite side.


55. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.


56. DISCONNECT FRONT AXLE ASSEMBLY RH

HINT:
Perform the same procedure as above on the opposite side.


57. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


58. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as above on the opposite side.


59. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A128798
    Set the engine lifter.

  1. A125676
    Remove the 7 bolts and nut, then remove the engine mounting insulator RH.

  1. A128799
    Remove the through bolt and nut, then separate the engine mounting insulator LH.

  1. A118689E01
    Remove the 6 bolts, and remove the engine assembly with transaxle and front suspension crossmember from the vehicle.


60. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  1. G036726
    Remove the bolts, then remove engine cover bracket No. 3.

  1. G036727
    Install the 2 engine hangers with 2 new bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 in.*lbf }

    NOTICE:
    Be sure to use new bolts to install the engine hanger.

  1. Using a chain block and engine sling device, hold engine with transaxle.

  1. A125776
    Remove the through bolt from the engine moving control rod and remove the front suspension crossmember.


61. REMOVE STATER ASSEMBLY (for Manual Transaxle)

A128367
  1. Remove the terminal cap.

  1. Separate the harness clamp.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.


62. REMOVE STATER ASSEMBLY (for Multi-Mode Manual Transaxle)

A128366
  1. Separate the harness clamp.

  1. Remove the bolt and remove the wire harness bracket.

  1. A128367
    Remove the terminal cap.

  1. Separate the harness clamp.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.


63. REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

C063143
  1. Remove the 7 bolts and the manual transaxle.


64. REMOVE MULTI-MODE MANUAL TRANSAXLE ASSEMBLY (for Multi-Mode Manual Transaxle)

  1. C098877
    Remove the 7 bolts and the multi-mode manual transaxle from the engine.


65. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

D025280E04
  1. Align the matchmark on the clutch cover assembly with the one on the flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


66. REMOVE CLUTCH COVER ASSEMBLY (for Multi-Mode Manual Transaxle)

D025280E04
  1. Align the matchmark on the clutch cover assembly with the one on the flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


67. REMOVE CLUTCH DISC ASSEMBLY

68. REMOVE FLYWHEEL SUB-ASSEMBLY

A099115E03
  1. Hold the crankshaft with SST.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 6 bolts and flywheel.

  1. Remove the crankshaft sensor plate.


69. REMOVE ENGINE WIRE

A128833
  1. Remove the lock knob and harness clamp.

  1. Disconnect the ECM connector.

  1. A104339
    Remove the 2 connectors and clamp from the engine room junction block and disconnect the wire harness.

  1. Disconnect all the wire harnesses and connectors. Make sure that no wire harness is connected between the body and engine.


70. REMOVE GENERATOR ASSEMBLY

A128374
  1. Remove the terminal cap.

  1. Separate the connector and harness clamp.

  1. Remove the nut and remove terminal B.

  1. A128375E01
    Remove fan belt adjusting slider fixing bolt A and nut B and remove the fan belt adjusting slider.

  1. A128376E01
    Remove fixing bolt C and remove the generator.


71. REMOVE TIMING CHAIN COVER NO.2

  1. A069329
    Remove the 2 bolts, then remove the timing cover No. 2.


72. REMOVE VACUUM PUMP ASSEMBLY

C129748
  1. Slide the clip and disconnect the vacuum hose.

  1. Disconnect the cam position sensor connector.

  1. C129749
    Remove the 2 bolts and vacuum pump.

  1. F048854
    Remove the 2 O-rings from the vacuum pump.


73. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the bolt, then remove the oil level gage guide.


74. REMOVE EGR COOLER PIPE SUB-ASSEMBLY

  1. A125674
    Disconnect the 2 water by-pass hoses.

  1. Remove the bolt and 4 nuts, then remove the EGR cooler assembly.

  1. Remove the 2 gaskets.


75. REMOVE VACUUM REGULATING VALVE ASSEMBLY

A125788E01
  1. Disconnect the connector clamp and connector.

  1. Disengage the 2 hose clamps and disconnect the 2 vacuum hoses.

  1. Remove the 3 bolts, then remove the vacuum regulating valve together with the bracket.


76. REMOVE EGR VALVE ASSEMBLY

  1. A125675
    Disconnect the EGR valve connector and hose.

  1. Remove the 2 nuts, then remove the EGR valve assembly.

  1. Remove the gasket.


77. REMOVE INTAKE AIR CONNECTOR

  1. G036729
    Disconnect the vacuum hose and the water hose.

  1. Remove the 4 bolts, then remove the intake air connector.


78. REMOVE EGR PIPE CONNECTOR

  1. A128827
    Remove the 3 bolts, then remove the EGR pipe connector.


79. REMOVE OIL COOLER HOSE SUB-ASSEMBLY

  1. G036731
    Remove the oil cooler hose.


80. REMOVE EGR PIPE NO. 1 HOSE

  1. G036732
    Remove EGR PIPE No. 1 hose.


81. REMOVE WATER BY-PASS PIPE NO. 1

  1. A128830
    Remove the 2 nuts and 2 bolts, then remove water by-pass pipe No. 1.


82. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

83. REMOVE GLOW PLUG NO. 1 CONNECTOR

  1. A098269
    Remove the 5 screw grommets.

  1. A098270
    Remove the nut and disconnect the glow terminal.

  1. Remove the 4 nuts and glow plug connector No. 1.


84. REMOVE GLOW PLUG ASSEMBLY

  1. A125733
    Using a 10 mm deep socket wrench, remove the 4 glow plugs.


85. REMOVE INJECTION PIPE CLAMP NO. 1

A098451
  1. Remove the 2 nuts, then remove injection pipe clamp No. 1.


86. REMOVE INJECTION PIPE CLAMP NO. 2

A098452
  1. Remove the nut, then remove injection pipe clamp No. 2.


87. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 1

A069347E01
  1. Using a spanner (13 mm), hold the injector steadily, and using SST, remove the injection pipe from the injector side.

    SST
    09023-38401  

  1. Using SST, remove the injection pipe from the common rail side.

    SST
    09023-38401  

  1. After removing the injection pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


88. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 2

HINT:
Perform the same procedure as for injection pipe No.1.


89. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 3

HINT:
Perform the same procedure as for injection pipe No.1.


90. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 4

HINT:
Perform the same procedure as for injection pipe No.1.


91. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

A098482E01
  1. Using a spanner (17 mm), hold the supply pump steady, and using SST, remove the fuel inlet pipe from the supply pump side.

    SST
    09023-38401  

  1. A098483E01
    Using SST, remove the fuel inlet pipe from the common rail side.
    SST
    09023-38401  

  1. After removing the fuel inlet pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


92. REMOVE COMMON RAIL ASSEMBLY

A098485
SST
09023-38401  
  1. Disconnect the 2 connectors.

  1. Disconnect the fuel hose.

  1. Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure sensor or fuel pressure regulator.


93. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

A098453
  1. Remove the 5 retainer springs, then remove the nozzle leakage pipe.


94. REMOVE INJECTOR ASSEMBLY

A098454E01

HINT:
  1. Each injector assembly has its own fuel injection part number. when replacing the injector assembly, store them in the correct order so that they can be returned to their original locations when reassembled.
  2. Arrange the injectors, clamps, washers, bolts and clamp seats in the correct order.

  1. Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 nozzle holder clamp seats.

  1. Disconnect the 4 injector connectors.

  1. Remove the 4 injectors from the cylinder head.

  1. Remove the 4 injection nozzle seats from the injector or cylinder head.

    NOTICE:
    When removing the injector, check that the injector nozzle seat is either attached to the injector, or remains in the cylinder head.


95. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

A125787
  1. Disconnect the 3 fuel hoses.

  1. Disconnect the 2 connectors.

  1. Remove the 3 bolts, then remove the supply pump.

  1. Remove the supply pump driving coupling.

  1. Remove the O-ring.

    NOTICE:
    When removing the supply pump, make sure that the drive coupling does not fall off, as it can be easily removed. If the drive coupling falls off, replace it with a new one.


96. REMOVE DIESEL ENGINE ENGINE COOLANT TEMPERATURE SENSOR

  1. A128829E01
    Using SST, remove the engine coolant temperature sensor.
    SST
    09817-33190  


97. REMOVE ENGINE COVER BRACKET NO. 2
  1. Disconnect the vacuum hose.

  1. Remove the 2 bolts, then remove the engine cover bracket.


98. REMOVE CONNECTOR TO VACUUM RESERVOIR TUBE

99. REMOVE CYLINDER HEAD COVER NO.2

A128828

100. REMOVE TURBO INSULATOR NO. 1

A098282
  1. Remove the 3 bolts and turbo insulator No. 1.


101. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

A126329
  1. Remove the bolt, and separate the manifold support bracket.

  1. Remove the 3 nuts and exhaust manifold converter.

  1. A098284
    Remove the gasket from the turbocharger.


102. REMOVE TURBO OIL INLET PIPE

A098287
  1. Remove the wire harness clamp.

  1. Remove the bolt.

  1. Remove the 2 union bolts, oil inlet pipe and 4 gaskets.


103. REMOVE TURBO CHARGER SUB-ASSEMBLY

G038744
  1. Remove the 2 nuts.

  1. A098289
    Disconnect the vacuum hose from the turbocharger.

  1. Remove the 3 nuts and turbocharger.

  1. A098290
    Remove the gasket from the exhaust manifold.

  1. G038742
    Remove the gasket from the turbocharger.


104. REMOVE TURBO OIL OUTLET PIPE

G038743
  1. Remove the 2 nuts and turbo oil outlet pipe.

  1. G038745
    Remove the gasket from the cylinder block.


105. REMOVE EXHAUST MANIFOLD
  1. Remove the 2 bolts, then remove the manifold stay.

  1. A128801
    Remove the 2 bolts, then remove exhaust manifold heat insulator No. 1.

  1. A128802
    Remove the 5 nuts, then remove the exhaust manifold with turbocharger.


106. REMOVE CYLINDER BLOCK SIDE COVER

  1. A128831
    Remove the 2 bolts, then remove the cylinder block side cover.


107. REMOVE CRANK POSITION SENSOR

  1. A098230
    Remove the bolt, then remove the crankshaft position sensor.


108. REMOVE ENGINE OIL LEVEL SENSOR

  1. G036736
    Remove the 4 bolts, then remove the engine oil level sensor.


109. REMOVE OIL PAN COVER

  1. G036737
    Remove the 3 bolts, then remove the oil pan cover.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →