2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C127609
    Install the transmission control cable with the 3 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C116858
    Connect the 2 cables and install the 2 clips.

  1. Install the 2 new clips onto the control cable bracket.

  1. C136389
    Securely push the control cable into the grooved part of the shift lever with the protrusion of the control cable facing upward.

  1. C127607
    Connect the control select cable to the shift lever with the clip.

    NOTICE:
    1. Connect the control select cable so that the adjusting mechanism lock of the control select cable is installed on the left side of the vehicle.
    2. Do not apply excessive load to the shift lever.

  1. C125963
    Connect the control shift cable to the shift lever.


2. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY

C125966
  1. Install the floor shift shift lever with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 8.9 ft.*lbf }


3. ADJUST TRANSMISSION CONTROL SELECT CABLE

C127618

NOTICE:
Make sure that the transmission and the shift lever are in the neutral positions before adjusting the select cable.

  1. Push the protrusion of the select cable toward the rear of the vehicle, turn the protrusion in the direction indicated by the arrow shown in the illustration and lock it.

  1. C127623
    Turn the protrusion of the select cable in the direction indicated by the arrow shown in the illustration and release the lock.


4. INSTALL FRONT FLOOR HEAT INSULATOR NO.2

C127608
  1. Install front floor heat insulator with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


5. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)

A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front Side):
    40.5 mm (1.594 in.)
    Minimum length (Rear Side):
    38.5 mm (1.516 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 exhaust pipe support No. 4.

  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    A115439

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


6. INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 2SZ-FE)

  1. A104634
    Using vernier calipers, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635E01
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports.

    A127393

  1. Install the exhaust pipe assembly front with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


7. CONNECT OXYGEN SENSOR CONNECTOR

8. INSTALL REAR CONSOLE BOX ASSEMBLY

B118993
  1. Engage the 2 clips and install the console box rear.

  1. Install bolt <F>.


9. INSTALL REAR CONSOLE BOX COVER

B118991
  1. Engage the 8 claws and install the console box rear cover.


10. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

11. INSTALL BATTERY CARRIER (for 1KR-FE)

C106985
  1. Install the battery carrier with the 4 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


12. INSTALL BATTERY CARRIER (for 2SZ-FE)

C106370
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 175 kgf*cm , 13 ft.*lbf }


13. INSTALL BATTERY TRAY

14. INSTALL BATTERY

15. INSTALL BATTERY HOLD DOWN CLAMP

16. INSTALL AIR CLEANER INLET NO.1 (for 2SZ-FE)

C127624
  1. Install air cleaner inlet No. 1.


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REMOVAL (from Nov 2005)COMPONENTS (from Aug 2005) →