2005-2008 Yaris · Service Manual BODY ELECTRICAL

Back Door Entry Lock Function does not Operate

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the back door lock switch is pushed, a lock switch ON signal is output to the certification ECU and request signals are transmitted to both the indoor electrical key oscillators and door electrical key oscillator (back door) by the certification ECU. The key responds to the certification ECU by transmitting the ID code upon receipt of the request signals, causing the certification ECU to verify the ID code. When the certification ECU determines that the ID code is valid, a door lock signal is transmitted to the main body ECU to lock the back door.

WIRING DIAGRAM

B127994E01

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. By following the tester screen display, check whether any DTCs are output.

    OK:
    No DTC output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART
OK


2. CHECK MANUAL DOOR LOCK OPERATION
  1. Check that the manual door lock function operates normally.

    OK:
    Manual door lock function operates normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (ONLY BACK DOOR LOCK / UNLOCK FUNCTIONS DO NOT OPERATE)
OK


3. CHECK WIRELESS DOOR LOCK OPERATION
  1. Check that the wireless door lock and unlock functions operate normally.

    OK:
    Wireless door lock and unlock functions operate normally.



NG
GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (W/ ENTRY AND START SYSTEM)
OK


4. READ VALUE OF DATA LIST (BACK DOOR LOCK SWITCH)
  1. Check the Data List to confirm the operation of the back door lock switch.

    Certification ECU:
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Tr/B-Door Lock
    Back door lock switch / ON or OFF
    ON: Back door lock switch is pushed
    OFF: Back door lock switch is not pushed
    -

    OK:
    ON (back door lock switch is pushed) appears on the screen.



NG
Go to step 6
OK


5. CHECK OPERATION OF CERTIFICATION ECU ASSEMBLY
  1. After replacing the certification ECU assembly with a normal one, check that the back door lock function operates normally.

    OK:
    Back door lock function operates normally.



NG
REPLACE MAIN BODY ECU
OK

END (CERTIFICATION ECU ASSEMBLY IS DEFECTIVE)

6. INSPECT BACK DOOR OUTSIDE HANDLE

  1. B107877
    Remove the back door outside handle.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Switch released
    10 kΩ or higher
    3 - 4
    Switch pressed in
    Below 1 Ω

  1. Reinstall the back door outside handle.



NG
REPLACE BACK DOOR OUTSIDE HANDLE
OK


7. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU ASSEMBLY - BACK DOOR LOCK SWITCH)

  1. B124233E01
    Disconnect the D60 certification ECU assembly connector.

  1. Disconnect the N6 back door lock /unlock switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D60-7 (TSW5) - N6-4 (UL)
    Below 1 Ω
    N6-3 (E) - Body ground
    Below 1 Ω
    D60-7 (TSW5) or N6-4 (UL) - Body ground
    10 kΩor higher

  1. Reconnect the switch connector.

  1. Reconnect the ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU ASSEMBLY


← Back Door Entry Lock and Unlock Functions do not Operate (from Aug 2005)PARTS LOCATION (from Aug 2005) →