2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

D031819
  1. Remove the manual transmission filler plug and the gasket from the manual transmission case.


2. REMOVE DRAIN PLUG SUB-ASSEMBLY

D031820
  1. Remove the drain plug and gasket from the manual transmission case.


3. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and the speedometer driven hole cover.

  1. Remove the O-ring from the speedometer driven hole cover.


4. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

C137194
  1. Remove the clutch release fork with the clutch release bearing from the front transaxle case.


5. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

C067602
  1. Remove the release bearing hub clip and the clutch release bearing from the clutch release fork.


6. REMOVE CLUTCH RELEASE FORK SUPPORT BOOT

C132156
  1. Remove the clutch release fork support boot from the release fork support.


7. REMOVE RELEASE FORK SUPPORT

C067604E04
  1. Remove the release fork support from the front transaxle case.


8. REMOVE CLUTCH RELEASE FORK BOOT

D030525
  1. Remove the clutch release fork boot from the front transaxle case.


9. REMOVE TRANSMISSION REVOLUTION SENSOR

D031823
  1. Remove the 2 bolts and transmission case protector.

  1. D031824
    Remove the transmission revolution sensor from the manual transmission case.

  1. Remove the O-ring from the transmission revolution sensor.


10. REMOVE BACK UP LIGHT SWITCH ASSEMBLY

D031827E01
  1. Using SST, remove the back up light switch and gasket from the manual transmission case.

    SST
    09817-16011  


11. REMOVE NEUTRAL POSITION SWITCH ASSEMBLY

D031828E01
  1. Using SST, remove the neutral position switch and gasket from the manual transmission case.

    SST
    09817-16011  


12. REMOVE LOCK BALL ASSEMBLY NO. 1

D032339
  1. Remove lock ball No. 1 from the manual transmission case.


13. REMOVE SHIFT AND SELECT ACTUATOR ASSEMBLY

D031825E01
  1. Remove the plug and gasket from the manual transmission case.

  1. While looking through the plug, check that the slit in the shift and select shaft is as shown in the illustration.
    If not, turn and adjust it with a screwdriver.

  1. C130327
    Remove the 6 bolts, wire harness clamp bracket and shift and select actuator from the manual transmission case.


14. FIX MANUAL TRANSAXLE ASSEMBLY

D030529
  1. Using 2 wooden blocks, fix the manual transaxle assembly.


15. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

D032340
  1. Remove the 9 bolts and 2 wire harness clamps.

  1. D031829
    Gently tap the protrusion of the manual transmission case cover with a hammer and remove it.

    NOTICE:
    Be careful not to damage the manual transmission case.


16. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

D032341
  1. Using a chisel and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.

  1. D032342
    Engage the 2 gears simultaneously to lock the transmission.

  1. Remove the manual transmission output shaft rear set nut.

  1. Disengage the double meshing of the gear.


17. REMOVE GEAR SHIFT FORK NO. 3

D032343
  1. Remove the shift fork set bolt from gear shift fork No. 3.

  1. C080343
    Remove hub sleeve No. 3 and gear shift fork No. 3 from transmission clutch hub No. 3.


18. INSPECT 5TH GEAR THRUST CLEARANCE

C080344
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.57 mm (0.0039 to 0.0224 in.)

    Maximum clearance:
    0.57 mm (0.0244 in.)

    If the clearance exceeds the maximum, replace transmission clutch hub No. 3, the 5th gear or the input shaft rear radial ball bearing.


19. INSPECT 5TH GEAR RADIAL CLEARANCE

C080345
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    KOYO made:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)
    NSK made:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    KOYO made:
    0.058 mm (0.0023 in.)
    NSK made:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


20. REMOVE TRANSMISSION CLUTCH HUB NO. 3

D030536
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. D032356
    Remove the synchromesh shifting key spring from transmission clutch hub No. 3.

  1. D032344E01
    Using SST, remove the transmission clutch hub No. 3, 5th gear and synchronizer ring No. 3 from the input shaft.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
    09950-60010   (09951-00200)

  1. D032357
    Remove the 3 synchromesh shifting keys and synchromesh shifting key spring No. 3 from transmission clutch hub No. 3.


21. REMOVE 5TH GEAR NEEDLE ROLLER BEARING

D032358
  1. Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.


22. REMOVE 5TH DRIVEN GEAR

D030538E01
  1. Using SST, remove the 5th driven gear from the output shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03011, 09957-04010)
    09950-60010   (09951-00190)


23. REMOVE BEARING RETAINER REAR

D030539E01
  1. Remove the 5 bolts and bearing retainer rear from the manual transmission case.


24. REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING

C080351
  1. Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.


25. REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING

C080352
  1. Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.


26. REMOVE REVERSE IDLER GEAR SHAFT BOLT

D032345
  1. Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the manual transmission case.


27. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING

C080353
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.


28. REMOVE SHIFT DETENTE BALL PLUG

D032351
  1. Using a hexagon wrench, remove the shift detente ball plug from the manual transmission case.


29. REMOVE LOCK BALL ASSEMBLY NO. 2

D032346
  1. Using a hexagon wrench, remove lock ball No. 2 from the manual transmission case.


30. REMOVE MANUAL TRANSMISSION CASE

D032347
  1. Remove the 3 bolts from the front transaxle case.

  1. D032348
    Remove the 13 bolts from the manual transmission case.

  1. C067642
    Gently tap the manual transmission case with a brass bar and hammer and remove it from the front transaxle case.

    NOTICE:
    Do not damage the manual transmission case or front transaxle case.

  1. Remove the 4 manual transmission case straight pins from the front transaxle case.


31. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

C080359
  1. Remove the reverse idler gear, thrust washer and reverse idler gear shaft from the front transaxle case.


32. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

C080360
  1. Remove the 2 bolts and reverse shift arm bracket from the front transaxle case.


33. REMOVE GEAR SHIFT FORK SHAFT NO. 2

C080361
  1. Remove the 2 bolts from gear shift fork No. 2 and gear shift head No. 1.

  1. C080362E01
    Remove gear shift fork shaft No. 2 and gear shift head No. 1 from the front transaxle case.


34. REMOVE GEAR SHIFT FORK SHAFT NO. 1

C080363
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. C080364
    Remove the shift fork set bolt and gear shift fork shaft No. 1 from gear shift fork No. 1.

  1. C080365E01
    Remove gear shift fork No. 1.


35. REMOVE GEAR SHIFT FORK SHAFT NO. 3

C080366
  1. Using 2 screwdrivers and a hammer, tap out the snap ring from gear shift fork shaft No. 3.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. C080367E01
    Remove shift fork shaft No. 3 with reverse shift fork and gear shift fork No. 2 from the front transaxle case.

  1. C080368
    Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.

  1. C080369
    Using 2 screwdrivers and a hammer, tap out the snap ring from shift fork shaft No. 3.

    HINT:
    Use a shop rag or piece of cloth to keep the snap ring from flying off.

  1. Remove the reverse shift fork from gear shift fork shaft No. 3.


36. REMOVE INPUT SHAFT ASSEMBLY

C080586
  1. Remove the input shaft assembly and output shaft assembly from the front transaxle case.


37. REMOVE DIFFERENTIAL CASE ASSEMBLY

C067656
  1. Remove the differential case assembly from the front transaxle case.


38. REMOVE MANUAL TRANSAXLE CASE RECEIVER

C067657
  1. Remove the bolt and manual transaxle case receiver from the front transaxle case.


39. REMOVE REVERSE RESTRICT PIN ASSEMBLY

D032350
  1. Using a hexagon wrench, remove the reverse restrict pin plug from the manual transmission case.

  1. D032349
    Using a pin punch (φ 5 mm) and a hammer, drive the slotted spring pin and reverse restrict pin out of the manual transmission case.


40. REMOVE OIL RECEIVER PIPE NO. 1

C067644
  1. Remove the bolt and oil receiver pipe No. 1 from the manual transmission case.

    NOTICE:
    Be careful not to damage oil receiver pipe No. 1.


41. REMOVE OIL RECEIVER PIPE NO. 2

C080374
  1. Remove the bolt and oil receiver pipe No. 2 from the manual transmission case.

    NOTICE:
    Be careful not to damage oil receiver pipe No. 2.


42. REMOVE BEARING LOCK PLATE

C067658
  1. Remove the bolt and bearing lock plate from the front transaxle case.


43. REMOVE TRANSMISSION MAGNET

C067659E04
  1. Remove the transmission magnet from the front transaxle case.


44. REMOVE INPUT SHAFT FRONT BEARING

C081783E01
  1. Using SST, remove the input shaft front bearing from the front transaxle case.

    SST
    09612-65014   (09612-01050, 09612-01060)


45. REMOVE FRONT TRANSAXLE CASE OIL SEAL

C081783E01
  1. Using SST, remove the front transaxle case oil seal from the front transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)


46. REMOVE OUTPUT SHAFT FRONT BEARING

C082141E01
  1. Using SST, remove the output shaft front bearing from the front transaxle case.

    SST
    09308-00010  

    NOTICE:
    Do not apply excessive force to the front transaxle case when removing the output shaft front bearing.


47. REMOVE OUTPUT SHAFT COVER

C067719
  1. Remove the output shaft cover from the front transaxle case.


48. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

C081785E01
  1. Using SST, remove the front differential case front tapered roller bearing (outer race) and plate washer from the front transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)

  1. C082145E01
    Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case.
    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00360)

    NOTICE:
    Be careful not to damage the bearing.


49. REMOVE TRANSMISSION CASE OIL SEAL

D032352
  1. Using a screwdriver and hammer, drive the transmission case oil seal out of the manual transmission case.

    NOTICE:
    Be careful not to damage the manual transmission case.


50. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

D032353E01
  1. Using SST and a hammer, remove the front differential case rear tapered roller bearing (outer race) and plate washer from the manual transmission case.

    SST
    09950-60010   (09951-00620)
    09950-70010   (09951-07200)

  1. C082144E01
    Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)

    NOTICE:
    Be careful not to damage the bearing.


51. REMOVE TRANSAXLE CASE OIL SEAL

C081787E02
  1. Using SST and a hammer, drive the transaxle case oil seal out of the front transaxle case.

    SST
    09950-60010   (09951-00600)
    09950-70010   (09951-07100)

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →