CAN Main Wire for Disconnection (LHD Models)
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
There may be an open circuit in the main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69Ω or higher.| Symptom |
Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 69Ω or higher. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
- After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
- Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
| 1. CHECK DLC3 |
Turn the ignition switch off.

- Standard resistance:
Tester Connection
Condition
Specified Condition
Proceed to
D15-6 (CANH) - D15-14 (CANL)
Ignition switch off
108 to 132 Ω
A
D15-6 (CANH) - D15-14 (CANL)
Ignition switch off
132 Ω or higher
B
- NOTICE:
- When the measured value is 132Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.
|
|
||||
| A | |
| 2. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C SIDE) |
Turn the ignition switch off.

Disconnect the D42 P-CAN J/C connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D42-11 (TOLH) - D42-22 (TOLH)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 3. CONNECT CONNECTOR |
Reconnect the P-CAN J/C connector.
| NEXT | |
| 4. CHECK CAN MAIN WIRE OR CONNECTOR (ECM) |
1NZ / 2NZ / 2SZ-FE engine:

Turn the ignition switch off.
Disconnect the A21 ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A21-41 (CANH) - A21-49 (CANL)
Ignition switch off
108 to 132 Ω
1KR-FE engine:

Turn the ignition switch off.
Disconnect the A32 ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A32-25 (CANH) - A32-33 (CANL)
Ignition switch off
108 to 132 Ω
1ND-TV engine:

Turn the ignition switch off.
Disconnect the A49 ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A49-24 (CANH) - A49-46 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 5. CONNECT CONNECTOR |
Reconnect the ECM connector.
| NEXT | |
| 6. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - ECM) |
Turn the ignition switch off.

Disconnect the D41 D-CAN J/C connector.
Measure the resistance.
- Standard resistance::
Tester Connection
Condition
Specified Condition
D41-4 (EFI) - D41-15 (EFI)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 7. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C) |
Turn the ignition switch off.

Disconnect the D41 D-CAN J/C connector.
Measure the resistance.
- Standard resistance::
Tester Connection
Condition
Specified Condition
D41-11 (TORH) - D41-22 (TORH)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 8. CONNECT CONNECTOR |
Reconnect the P-CAN J/C connector.
| NEXT | |
| 9. CHECK CAN MAIN WIRE OR CONNECTOR (POWER STEERING ECU) |
Turn the ignition switch off.

Disconnect the D31 power steering ECU connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D31-1 (CANH) - D31-7 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 10. CONNECT CONNECTOR |
Reconnect the power steering ECU connector.
| NEXT | |
| 11. CHECK CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (P-CAN J/C - POWER STEERING ECU) |
Turn the ignition switch off.

Disconnect the D42 P-CAN J/C connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D42-4 (EPS) - D42-15 (EPS)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
