2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

CAN Main Wire for Disconnection (RHD Models)

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69Ω or higher.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 69Ω or higher.
  1. CAN main wire or connector
  2. D-CAN J/C (Junction connector)
  3. P-CAN J/C (Junction connector)
  4. ECM
  5. Power steering ECU

WIRING DIAGRAM

C132687E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK DLC3

  1. C118856E31
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    A
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    132 Ω or higher
    B

    NOTICE:
    When the measured value is 132Ωor higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



B
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
A


2. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C SIDE)

  1. C125896E14
    Turn the ignition switch off.

  1. Disconnect the P-CAN J/C connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-11 (TORH) - D41-22 (TORH)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 8
NG


3. CONNECT CONNECTOR
  1. Reconnect the P-CAN J/C connector.


NEXT


4. CHECK CAN MAIN WIRE OR CONNECTOR (POWER STEERING ECU)

  1. G100242E27
    Turn the ignition switch off.

  1. Disconnect the D31 power steering ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-1 (CANH) - D31-7 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE POWER STEERING ECU
NG


5. CONNECT CONNECTOR
  1. Reconnect the power steering ECU connector.


NEXT


6. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - POWER STEERING ECU)

  1. C125896E15
    Turn the ignition switch off.

  1. Disconnect the D42 D-CAN J/C connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (D-CAN J/C - POWER STEERING ECU (CAN-H, CAN-L))
OK


7. CHECK CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C)

  1. C125896E16
    Turn the ignition switch off.

  1. Disconnect the D42 D-CAN J/C connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D42-11 (TOLH) - D42-22 (TOLH)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))
OK

REPLACE D-CAN J/C (JUNCTION CONNECTOR)

8. CONNECT CONNECTOR
  1. Reconnect the P-CAN J/C connector.


NEXT


9. CHECK CAN MAIN WIRE OR CONNECTOR (ECM)

  1. C125895E07
    1NZ / 2NZ / 2SZ-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A21 ECM connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A21-41 (CANH) - A21-49 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. C118186E03
    1KR-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A32 ECM connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A32-25 (CANH) - A32-33 (CANL)
      Ignition switch off
      108 to 132 Ω

  1. C130899E03
    1ND-TV engine:
    1. Turn the ignition switch off.

    2. Disconnect the A49 ECM connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A49-24 (CANH) - A49-46 (CANL)
      Ignition switch off
      108 to 132 Ω



OK
REPLACE ECM
NG


10. CONNECT CONNECTOR
  1. Reconnect the ECM connector.


NEXT


11. CHECK CAN MAIN WIRE OR CONNECTOR (P-CAN J/C - ECM)

  1. C125896E17
    Turn the ignition switch off.

  1. Disconnect the P-CAN J/C connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D42-4 (EFI) - D42-15 (EFI)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (P-CAN J/C - ECM (CAN-H, CAN-L))
OK

REPLACE P-CAN J/C (JUNCTION CONNECTOR)


← Open in One Side of CAN Branch Line (from Aug 2005)CAN Main Wire for Disconnection (LHD Models) (from Aug 2005) →