2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.


1. INSTALL FUEL RETURN TUBE SUB-ASSEMBLY

A118830
  1. Install the fuel return tube onto the fuel tank.


2. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118829
  1. Install the fuel tank main tube onto the fuel tank.


3. INSTALL FUEL TANK TO FILLER PIPE HOSE

A126486
  1. Install the fuel tank to filler pipe hose with the hose clamp.

  1. Tighten the hose clamp bolt.


4. INSTALL FUEL TANK ASSEMBLY

A118825
  1. Clean the bolt holes and remove any grease.

  1. Install the fuel tank with 4 new bolts.

    Torque:
    14 N*m{ 146 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not reuse the bolt.


5. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY

A118821E01
  1. Align the fuel tube connector with the pipe, push the fuel tube connector in until the retainer makes a click sound, then lock the cover of the connector.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting the pipe and fuel tube connector, pull them to make sure that they are securely connected.


6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118819E01
  1. Align the fuel tube connector with the pipe, push the fuel tube connector in until the retainer makes a click sound, then lock the cover of the connector.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting the pipe and fuel tube connector, pull them to make sure that they are securely connected.


7. CONNECT FUEL TANK TO FILLER PIPE HOSE

A126484E01
  1. Connect the fuel tank to filler pipe hose with the hose clamp.

    NOTICE:
    Make sure that the hose clamp is at the correct angle when installing it.

  1. Tighten the hose clamp bolt.


8. CONNECT FUEL TANK BREATHER HOSE

A126485E01
  1. Connect the fuel tank breather hose with the hose clamp.

  1. Tighten the hose clamp bolt.


9. INSTALL FUEL TANK PROTECTOR NO. 1

A118817
  1. Install fuel tank protector No. 1 with the bolt, nut and clip.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


10. INSTALL FUEL TANK SUCTION TUBE GASKET

A118738
  1. Install a new fuel tank suction tube gasket onto the fuel tank.


11. INSTALL FUEL TANK VENT TUBE WITH SENDER GAUGE ASSEMBLY

A118815
  1. Align the protrusion of the fuel tank vent tube with sender gauge with the cutout of the fuel tank and install the fuel tank vent tube with sender gauge assembly.

    NOTICE:
    The arm of the sender gauge should not be bent.


12. INSTALL FUEL PUMP GAUGE RETAINER
  1. Align the end of the threads of a new fuel pump gauge retainer with that of the fuel tank.

  1. A118812E01
    Set SST to the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    1. Use SST. Do not use any other tools such as a screwdriver.
    2. As the fuel pipes are located on the track of SST, SST should be reset a few times to prevent it from coming into contact with the pipes when installing the fuel pump gauge retainer.

    HINT:
    Fit the rib on the fuel pump gauge retainer into the cutout of SST.

  1. A118813E01
    While holding the fuel pump assembly by hand, use SST to tighten the fuel pump gauge retainer one and half turns so that the mark on the retainer is within the range indicated in the illustration.


13. CONNECT FUEL RETURN TUBE SUB-ASSEMBLY
  1. Insert the fuel tank return tube.

  1. Install the tube joint clip.

    A118811E01

    NOTICE:
    1. Check that there are no scratches or foreign matter on the joint.
    2. Make sure that the fuel tank main tube is inserted all the way to the end.
    3. Check that the tube joint clip is installed onto the rim of the fuel tank main tube.
    4. After connecting the fuel tube connector and the fuel pipe, check that they are securely connected by pulling on them.
    5. Do not damage any clips. If a clip is damaged, replace it.


14. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
  1. Insert the fuel tank main tube.

  1. Install the tube joint clip.

    A118809E01

    NOTICE:
    1. Check that there are no scratches or foreign matter on the joint.
    2. Make sure that the fuel tank main tube is inserted all the way to the end.
    3. Check that the tube joint clip is installed onto the rim of the fuel tank main tube.
    4. After connecting the fuel tube connector and the fuel pipe, check that they are securely connected by pulling on them.
    5. Do not damage any clips. If a clip is damaged, replace it.


15. INSTALL REAR FLOOR SERVICE HOLE COVER

A118807
  1. Connect the fuel sender gauge connector.

  1. A118729E01
    Install the rear floor service hole cover with new butyl tape.

  1. A118713
    Install the floor carpet with the clip.


16. INSTALL REAR SEAT ASSEMBLY

  1. B124363E01
    Insert the 2 locating pins through the 2 body holes and install the rear seat.

  1. Using "Torx" socket wrench E10, install the 4 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. B124331E01
    Install the rear seat cushion.

  1. Using "Torx" socket wrench E10, install the 3 bolts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }


17. INSTALL NO. 2 REAR SEAT LEG COVER

  1. B124330
    Engage the 6 claws and install the No. 2 rear seat leg cover.


18. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

  1. B106445
    Install the deck floor box and lock the 2 knobs.


19. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Install the spare wheel cover.


20. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106447
    Set the deck board and lock the 2 knobs.


21. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

  1. B138392
    Install the rear floor carpet.


22. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.


23. ADD FUEL

24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


25. CHECK FOR FUEL LEAK
← REMOVAL (from Nov 2005)PRECAUTION (Aug 2005 – Dec 2005) →