2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

  1. B114569E01
    Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.


3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

  1. B106371
    Release the 2 knobs and remove the deck board.


4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)

  1. B138393
    Remove the spare wheel cover.


5. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

  1. B106373
    Release the 2 knobs and remove the deck floor box.


6. REMOVE REAR FLOOR CARPET (w/o Deck Board)

  1. B138392
    Remove the rear floor carpet.


7. REMOVE NO. 2 REAR SEAT LEG COVER

  1. B124330
    Disengage the 6 claws and remove the No. 2 rear seat leg cover.


8. REMOVE REAR SEAT ASSEMBLY

  1. B124331
    Using "Torx" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.

  1. B124315
    Using "Torx" socket wrench E10, remove the 4 bolts and the rear seat.


9. REMOVE REAR FLOOR SERVICE HOLE COVER

A118713
  1. Remove the clip from the floor carpet.

  1. A118728
    Remove the rear floor service hole cover.

  1. A118807
    Disconnect the sender gauge connector.


10. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118808
  1. Widen the tip of the tube joint clip and pull it out.

  1. Pull out the fuel tank main tube to disconnect it.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube joint has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag.
    6. If the nylon tube and fuel suction plate are stuck, push and pull to release them.


11. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY

A118810
  1. Widen the tip of the tube joint clip and pull it out.

  1. Pull out the fuel tank main tube to disconnect it.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube joint has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag.
    6. If the nylon tube and fuel suction plate are stuck, push and pull to release them.


12. REMOVE FUEL PUMP GAUGE RETAINER

A118812E01
  1. Using SST, remove the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Align the claws of the fuel pump gauge retainer and the tips of SST.


13. REMOVE FUEL TANK VENT TUBE WITH SENDER GAUGE ASSEMBLY

A118814
  1. Remove the fuel tank vent tube with sender gauge from the fuel tank.

    NOTICE:
    Do not bend the arm of the sender gauge.


14. REMOVE FUEL TANK SUCTION TUBE GASKET

A118738
  1. Remove the fuel suction tube gasket from the fuel tank.


15. DRAIN FUEL

16. REMOVE FUEL TANK PROTECTOR NO. 1

A118816E01
  1. Pinch and remove the clip as shown in the illustration.

  1. Remove the bolt and nut and remove fuel tank protector No. 1.


17. DISCONNECT FUEL TANK BREATHER HOSE

A126482
  1. Loosen the clamp bolt, and disconnect the fuel tank breather hose.


18. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

A126483
  1. Loosen the clamp bolt, and disconnect the fuel tank to filler pipe hose.


19. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118818E01
  1. Release the lock as shown in the illustration, then pull and remove the fuel tank main tube.

    NOTICE:
    1. Remove any dirt and foreign matter from the clip before performing this work.
    2. Avoid any scratches or disconnection, as the quick connector has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with a plastic bag.
    6. If the connector and pipe are stuck, disconnect the nylon tube by turning it by hand to release it.


20. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY

A118820E01
  1. Release the lock as shown in the illustration, then pull and remove the fuel tank return tube.

    NOTICE:
    1. Remove any dirt and foreign matter from the clip before performing this work.
    2. Avoid any scratches or disconnection, as the quick connector has the O-ring that seals the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with a plastic bag.
    6. If the connector and pipe are stuck, disconnect the nylon tube by turning it by hand to release it.


21. REMOVE FUEL TANK ASSEMBLY

A118825
  1. Set a transmission jack under the fuel tank.

  1. Remove the 4 bolts and the fuel tank.


22. REMOVE FUEL TANK TO FILLER PIPE HOSE

A126486
  1. Loosen the hose clamp, and remove the fuel tank to filler pipe hose.


23. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

A118829
  1. Remove the fuel tank main tube from the fuel tank.


24. REMOVE FUEL RETURN TUBE SUB-ASSEMBLY

A118830
  1. Remove the fuel return tube from the fuel tank.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →