2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. REMOVE FRONT TIRE

3. REMOVE ENGINE UNDER COVER RH

4. REMOVE ENGINE UNDER COVER LH

5. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A117319
    Install a vinyl hose onto the radiator.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the water drain plug, then drain the coolant.

    A128298E01


6. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.

  1. D025304E03
    Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause problems.
    1. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


7. DRAIN MULTI-MODE MANUAL TRANSAXLE OIL (for Multi-Mode Manual Transaxle)

D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the filler plug opening.

    NOTICE:
    1. An excessively large or small amount of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. When the oil level is low, check for oil leakage.

  1. Install the filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


8. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


11. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


13. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


15. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


16. REMOVE WINDSHIELD WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


17. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

  1. A118801E01
    Disengage the claws and remove cowl to resister duct No. 2.


18. REMOVE COWL TOP PANEL OUTER

  1. A131386
    Disengage the clamp and separate the wiper motor connector.

  1. A131385
    Remove the 9 bolts and the cowl top panel outer.


19. REMOVE BATTERY

  1. A116495
    Disconnect the negative battery terminal.

  1. Disconnect the positive battery terminal.

  1. A104324
    Loosen the nut and remove the battery carrier camp.

  1. Remove the battery from the vehicle.


20. REMOVE BATTERY TRAY

21. REMOVE BATTERY CARRIER
  1. Separate the 4 wire harnesses.

  1. A108954
    Remove the 5 bolts and remove the battery carrier.


22. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A127601
  1. Remove the air cleaner inlet from the reservoir tank.

  1. Disengage the clamp of the air cleaner cap and remove the air cleaner cap.


23. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

24. DISCONNECT FAN AND GENERATOR V BELT

A127651E01
  1. Loosen bolts A and B.

  1. Turn adjusting bolt C to release the tension and remove the V belt from the pulleys.


25. REMOVE WITH PULLEY COMPRESSOR ASSEMBLY

A108955
  1. Separate the connector and clamp.

  1. Remove the 3 bolts and separate the cooler compressor assembly.

    HINT:
    Remove the cooler compressor assembly together with the low and high pressure hoses, then suspend them from the body with a piece of rope.


26. DISCONNECT NO. 1 RADIATOR HOSE

A127602
  1. Loosen the clamp and separate No. 1 radiator hose.


27. DISCONNECT NO. 2 RADIATOR HOSE

A127603
  1. Loosen the clamp and separate the No. 2 radiator hose.


28. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A127212
    Disconnect the No. 1 fuel vapor feed hose.


29. DISCONNECT FUEL HOSE SUB-ASSEMBLY

A127194
  1. Remove the fuel delivery pipe clamp.

  1. A127202E01
    Pinch the fuel tube connector retainer from both sides, disconnect the fuel tube connector and separate the fuel tube from the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.


30. DISCONNECT HEATER WATER INLET HOSE A

A129159
  1. Separate the heater water inlet hose.

  1. A127604
    Separate the water by-pass hose.


31. DISCONNECT HEATER WATER OUTLET HOSE A

A129160
  1. Separate the heater water outlet hose.

  1. A127605
    Separate the water by-pass hose.


32. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

A129214
  1. Disconnect the union to connector tube hose.


33. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

A129215
  1. Disconnect the union to connector tube hose.


34. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

A127606
  1. Remove the 2 bolts and remove the clutch release cylinder cover.

  1. A127607
    Remove the 4 bolts and separate the clutch release cylinder.

  1. Suspend the clutch release cylinder from the vehicle with a piece of rope.


35. SEPARATE FLOOR SHIFT CABLE TRANSMISSION CONTROL SELECT (for Manual Transaxle)

A127608
  1. Remove the 2 bolts and 2 clips and remove the floor shift cable transmission control select.


36. DISCONNECT CONNECTOR (for Multi-Mode Manual Transaxle)
  1. Remove the bolt and the wire harness clamp and remove the wire harness from the transaxle.


37. DISCONNECT ENGINE WIRE

A127609
  1. Remove the bolt and the wire harness clamp and remove the wire harness from the transaxle.

  1. A127610
    Disconnect the 2 connectors shown in the illustration.

  1. A127611
    Remove the connector and 2 clamps from the engine room junction block and separate the wire harness clamp.

  1. A127612
    Remove the 3 clamps and the band and disconnect the No. 2 oxygen sensor connector.

  1. A135335E01
    Wile gently pushing portion A, push lock button B and turn the lever.

    HINT:
    The lever release operation is completed by turning the lever approximately 90° until it makes a click sound.

  1. Disconnect all the wire harnesses and connectors. Make sure that no wire harnesses between the body and engine are connected.


38. REMOVE COLUMN HOLE COVER SILENCER SHEET

A127614
  1. Remove the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.


39. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

A127615
  1. Use a seat belt to fix the steering wheel assembly so that the steering wheel does not turn.

    HINT:
    Perform this work in order to avoid breakage of the spiral cable.

  1. A127616E01
    Place a matchmark on the sliding yoke and the power steering.

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.


40. REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

A127617E01
  1. Remove clip A, separate clip B from the body and remove the No. 1 steering column hole cover.

    NOTICE:
    Do not damage clips A and B.


41. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 4 bolts and 4 compression springs.

  1. Remove the 2 No. 4 exhaust pipe supports and the exhaust pipe assembly tail.


42. REMOVE FRONT AXLE SHAFT LH NUT

C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.


43. REMOVE FRONT AXLE HUB RH NUT

HINT:
The separation procedure for the RH side is the same as that for the LH side.


44. SEPARATE FRONT SPEED SENSOR LH

C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.

  1. C112274
    Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.


45. SEPARATE FRONT SPEED SENSOR RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


46. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C116895E01
    Using SST, separate the tie rod end from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.


47. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


48. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Remove the nut and separate the stabilizer link from the shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


49. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


50. SEPARATE FRONT NO. 2 SUSPENSION ARM SUB-ASSEMBLY LOWER LH

C107513
  1. Remove the clip and castle nut.

  1. C107514E01
    Using SST, separate the lower arm.
    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.


51. SEPARATE FRONT NO. 2 SUSPENSION ARM SUB-ASSEMBLY LOWER RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


52. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.

  1. C125277
    Remove the 2 nuts and 2 bolts and remove the front axle assembly.

    HINT:
    Keep the nut from rotating while turning the bolt.


53. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.


54. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


55. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.


56. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A127618
    Set the engine lifter.

  1. A127619
    Remove the 5 bolts and nut and remove the engine mounting insulator RH.

  1. A127620
    Remove the through bolt and nut and separate the engine mounting insulator LH.

  1. A127621
    Operate the engine lifter, remove the 6 bolts, and remove the engine assembly with transaxle and the front suspension cross member from the vehicle.


57. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A127622
  1. Install engine hanger No. 1 and engine hanger No. 2 with the bolts, as shown in the illustration.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    No. 1 engine hanger
    12281 - 23021
    No. 2 engine hanger
    12282 - 23010
    bolt
    91641 - 80820

  1. Using an engine sling devise and chain block, suspend the engine assembly with transaxle and the front suspension crossmember.

  1. A127623
    Remove the through bolt shown in the illustration and remove the front suspension crossmember.


58. REMOVE STARTER ASSEMBLY

  1. A128269
    Remove the terminal cap.

  1. Remove the nut and disconnect terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.


59. REMOVE FAN AND GENERATOR V BELT
  1. Remove the fan and generator V belt.


60. REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

C116849
  1. Remove the 9 bolts and the manual transaxle.


61. REMOVE MULTI-MODE MANUAL TRANSAXLE ASSEMBLY (for Multi-Mode Manual Transaxle)

  1. C136391E01
    Remove the 9 bolts and multi-mode manual transaxle from the engine.


62. REMOVE CLUTCH COVER ASSEMBLY

D025280E02
  1. Align the matchmark on the clutch cover with the one on the flywheel.

  1. Loosen each set bolt by one turn at a time until the spring tension is released.

  1. Remove the set bolts and the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


63. REMOVE CLUTCH DISC ASSEMBLY

NOTICE:
Keep the lining part of the clutch disk and the surfaces of the pressure plate and flywheel free of oil and foreign matter.


64. REMOVE FLYWHEEL SUB-ASSEMBLY

A129213E01
  1. w/o service hole:

    1. Using SST, hold the crankshaft pulley.

      SST
      09960-10010   (09963-01000, 91651-60855)

  1. A131374E01
    w/ service hole:

    1. Using SST, hold the crankshaft pulley.

      SST
      09330-00021  
      09213-54015   (91651-60855)

  1. A131380
    Remove the 6 bolts and 2 flywheel spacers with flywheel.


65. REMOVE REAR END PLATE

A109091
  1. Remove the bolt and the rear end plate.


66. REMOVE AIR CLEANER ASSEMBLY

A127625
  1. Remove the bolt and the fuel vapor feed hose and remove the VSV.

  1. Separate the intake air flow meter connector.

  1. Remove the 3 bolts and remove the air cleaner case.


67. REMOVE ENGINE WIRE
  1. Separate the sensor connectors and the wire harness clamps from the engine assembly and remove the engine wire harness.


68. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

A127626
  1. Remove the 3 bolts and remove the No. 1 exhaust manifold heat insulator.


69. REMOVE MANIFOLD STAY

A127627
  1. Remove the bolt and the nut and remove the manifold stay.


70. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A135336
    Remove the bolt and wire harness clamp.

  1. A127628E02
    Remove the 3 bolts and 2 nuts and remove the exhaust manifold converter.


71. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

A108582
  1. for DENSO, YAZAKI made:

    1. Using a 22 mm (0.8661 in.) deep socket wrench, remove the oil pressure switch.

  1. A131381
    for JAEGER made:

    1. Using a 24 mm (0.9449 in.) deep socket wrench, remove the oil pressure switch.


72. REMOVE NO.2 IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127630
  1. Remove the bolt and the washer and remove No. 2 idler pulley.


73. REMOVE IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127631
  1. Remove the nut with the washer and remove the idler pulley.


74. REMOVE WATER PUMP PULLEY

A127226E01
SST
09960-10010   (09963-00500)
  1. Using SST, hold the water pump pulley and remove the 4 bolts.


75. REMOVE FAN BELT ADJUSTING BAR

A127634
  1. Remove the 2 bolts and remove the fan belt adjusting bar.


76. REMOVE GENERATOR ASSEMBLY

A127635
  1. Remove the through bolt and the nut and remove the generator assembly.


77. REMOVE WATER PUMP ASSEMBLY

A127636
  1. Remove the 3 bolts and 2 nuts and remove the water pump assembly.


78. REMOVE THROTTLE BODY ASSEMBLY

A127637
  1. Separate the No.2 ventilation hose.

  1. A127638
    Remove the 3 bolts and remove the throttle body assembly.


79. REMOVE THROTTLE BODY BRACKET

A127639
  1. Remove the 2 bolts and remove the throttle body bracket.


80. REMOVE VENTILATION HOSE

A127640
  1. Separate the No. 2 ventilation hose.


81. REMOVE INTAKE MANIFOLD

A127641E01
  1. Remove the 3 bolts and 2 nuts and remove the intake manifold.


82. REMOVE KNOCK SENSOR

A109109
  1. Remove the nut and remove the knock sensor.


83. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

A127642
  1. Remove the 2 bolts and remove the fuel delivery pipe and the fuel tube together with the fuel injector.

    NOTICE:
    Do not drop the fuel injectors.

  1. Remove the 2 fuel pipe insulators.


84. REMOVE FUEL INJECTOR ASSEMBLY

  1. A127204
    Remove the 4 injectors from the delivery pipe sub-assembly.

  1. A107004E01
    Remove the O-ring and insulator from each injector.

  1. A127656
    Remove the 2 insulators from the delivery pipe sub-assembly.


85. DISCONNECT NO. 1 RADIATOR HOSE

A127643
  1. Loosen the clamp and remove the No. 1 radiator hose.


86. DISCONNECT NO. 2 RADIATOR HOSE

A127644
  1. Loosen the clamp and remove the No. 2 radiator hose.


87. REMOVE RADIO SETTING CONDENSER

A127645
  1. Remove the bolt and remove the radio setting condenser.


88. REMOVE WATER INLET

A127646
  1. Remove the bolt and the nut and remove the water inlet.


89. REMOVE THERMOSTAT

A127647
  1. Remove the thermostat.


90. REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR

A127648
  1. Using a 19 mm deep socket wrench, remove the E.F.I. coolant temperature sensor.


91. REMOVE IGNITION COIL ASSEMBLY

A127649
  1. Remove the 4 bolts and remove the 4 ignition coil assemblis.


92. REMOVE SPARK PLUG

93. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY
← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →