2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY

2. INSTALL SPARK PLUG

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }


3. INSTALL IGNITION COIL ASSEMBLY

A127649
  1. Install the ignition coil assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


4. INSTALL E.F.I. ENGINE COOLANT TEMPERATURE SENSOR

A127648
  1. Using a 19mm deep socket wrench, install the E.F.I. water temperature through a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


5. INSTALL THERMOSTAT

A127231
  1. Install a new gasket onto the thermostat.

  1. Align the matchmark of the water inlet with the jiggle valve of the thermostat and install the thermostat.


6. INSTALL WATER INLET

A127646
  1. Install the water inlet with the bolt and the nut.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


7. INSTALL RADIO SETTING CONDENSER

A127645
  1. Install the radio setting condenser with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


8. CONNECT NO. 2 RADIATOR HOSE

A127644
  1. Connect No. 2 radiator hose with the clip.


9. CONNECT NO. 1 RADIATOR HOSE

A127643
  1. Connect No. 1 radiator hose with the clip.


10. INSTALL FUEL INJECTOR ASSEMBLY

  1. A127656
    Install the 2 insulators onto fuel delivery pipe.

  1. A107004E01
    Apply a light coat of gasoline to 4 new O-rings and 4 new insulators, then install one onto each fuel injector.

  1. Apply a light coat of gasoline to the contact surfaces of the fuel delivery pipe and the O-rings and insulators of the fuel injector.

  1. A127205
    While turning the fuel injectors left and right, install them onto the fuel delivery pipe.

    NOTICE:
    1. Do not twist the O-ring.
    2. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.


11. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Install the fuel delivery pipe insulator.

  1. A127642
    Provisionally install the fuel delivery pipe and the fuel tube with the 2 bolts.

    NOTICE:
    Do not drop the fuel injector when assembling the fuel delivery pipe.

  1. Check that the fuel injector turns smoothly.

    NOTICE:
    If the result is not as specified, replace the O-ring with a new one and reinstall the fuel delivery pipe.

  1. Tighten the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


12. INSTALL KNOCK CONTROL SENSOR

  1. A107019E01
    Install the knock sensor, in the direction shown in the illustration with the nut.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Connect the knock sensor connector.


13. INSTALL INTAKE MANIFOLD
  1. Install a new intake manifold gasket.

  1. A127169
    Provisionally install the intake manifold with the 3 bolts and 2 nuts.

  1. A109351
    Tighten the 3 bolts and 2 nuts in the sequence order shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


14. INSTALL VENTILATION HOSE

A127640
  1. Connect the ventilation hose.


15. INSTALL THROTTLE BODY BRACKET

A127639
  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


16. INSTALL THROTTLE BODY ASSEMBLY

A127638E01
  1. Install the throttle body assembly with the 3 bolts through a new gasket.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } bolt A
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf } bolt B

  1. A127637
    Connect the No. 2 ventilation hose.


17. INSTALL WATER PUMP ASSEMBLY

A127636
  1. Install the water pump assembly with the 3 bolts and 2 nuts through a new gasket.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


18. INSTALL GENERATOR ASSEMBLY

A127635
  1. Provisionally install the generator assembly with the through bolt and the nut.


19. INSTALL FAN BELT ADJUSTING BAR

A127634E01
  1. Provisionally install the fan belt adjusting bar with the 2 bolts.

  1. Tighten bolt A.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


20. INSTALL WATER PUMP PULLEY
  1. Provisionally install the water pump pulley with the 4 bolts.

  1. A127226E01
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09963-00500)

  1. Tighten the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


21. INSTALL IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127631
  1. Install the idler pulley with the nut.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }


22. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

A127630
  1. Install idler pulley No. 2 with the bolt and the washer.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }


23. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Apply adhesive 1324 to 2 or 3 end thread of the engine oil pressure switch assembly.

  1. A127629
    for DENSO, YAZAKI made:

    1. Using a 22 mm (0.8661 in.) deep socket wrench, install the oil pressure switch.

      Torque:
      15 N*m{ 153 kgf*cm , 11 ft.*lbf }

      NOTICE:
      Do not start the engine for at least one hour after the installation.

  1. for JAEGER made:

    1. Using a 24 mm (0.9449 in.) deep socket wrench, install the oil pressure switch.

      Torque:
      15 N*m{ 153 kgf*cm , 11 ft.*lbf }

      NOTICE:
      Do not start the engine for at least one hour after the installation.


24. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A135336
    Install the bolt and wire harness clamp.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the exhaust manifold converter through a new gasket.

  1. A131352E01
    Install the exhaust manifold converter with the 3 bolts and 2 nuts, in the sequence shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


25. INSTALL MANIFOLD STAY

A127627E01
  1. Install the manifold stay with the bolt and the nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } bolt
    18 N*m{ 184 kgf*cm , 13 ft.*lbf } nut


26. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

A127626
  1. Install No. 1 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    8.0 N*m{ 76 kgf*cm , 66 in.*lbf }


27. INSTALL ENGINE WIRE

28. INSTALL AIR CLEANER ASSEMBLY

A127625E01
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf } bolt A

  1. Connect the intake air flow meter connector.

  1. Install the VSV with the bolt and connect the fuel vapor feed hose.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf } bolt B


29. INSTALL REAR END PLATE

A109091
  1. Install the rear end plate with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


30. INSTALL FLYWHEEL SUB-ASSEMBLY

A129213E01
  1. w/o service hole:

    1. Hold the crankshaft pulley with SST.

      SST
      09960-10010   (09963-00500)

  1. A131374E01
    w/ service hole:

    1. Hold the crankshaft pulley with SST.

      SST
      09330-00021  
      09213-54015   (91651-60855)

  1. A131380
    Install the flywheel through the 2 flywheel spacers with the 6 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }


31. INSTALL CLUTCH DISC ASSEMBLY

F100378E01
  1. Insert SST into the clutch disc, and then insert them into the flywheel.

    SST
    09301-00210  

    NOTICE:
    Insert the clutch disc in the correct direction.


32. INSTALL CLUTCH COVER ASSEMBLY

D026323E02
  1. Align the matchmark on the clutch cover with the one on the flywheel.

  1. Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin at the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    After checking that the disc is in the center, gently move SST up and down, right and left to tighten the bolts.

    SST
    09301-00210  


33. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the V belt onto the pulleys.


34. INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

C116849E01
  1. Align the input shaft with the clutch disc and install the manual transaxle onto the engine.

  1. Install the 9 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt A
    39 N*m{ 398 kgf*cm , 29 ft.*lbf } for bolt B

    NOTICE:
    1. Insert dowel pins into dowel holes securely so that the end face of transaxle assembly fits close against engine assembly before tightening the bolts between the engine and transaxle.
    2. Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.


35. INSTALL MULTI-MODE MANUAL TRANSAXLE ASSEMBLY (for Multi-Mode Manual Transaxle)

  1. C136391E02
    Align the input shaft with the clutch disc and install the manual transaxle onto the engine.

  1. Install the 9 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt A
    39 N*m{ 398 kgf*cm , 29 ft.*lbf } for bolt B

    NOTICE:
    1. Insert dowel pins into dowel holes securely so that the end face of transaxle assembly fits close against engine assembly before tightening the bolts between the engine and transaxle.
    2. Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.


36. INSTALL STARTER ASSEMBLY

  1. A128269
    Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the connector.

  1. Connect terminal 30 with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.


37. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A127622
  1. Install No. 1 engine hanger and No. 2 engine hanger with the bolts, as shown in the illustration.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    No. 1 engine hanger
    12281 - 23021
    No. 2 engine hanger
    12282 - 23010
    bolt
    91641 - 80820

  1. Using an engine sling devise and chain block, suspend the engine assembly with transaxle.

  1. A127623
    Install the front suspension crossmember onto the engine assembly with transaxle using the through bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }


38. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

  1. A127618
    Set the engine lifter.

  1. A127620
    Install the engine mounting insulator LH with the through bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A127619E01
    Install the engine mounting insulator RH with the 5 bolts and the nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } bolt
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } nut

  1. A127621E01
    Operate the engine lifter and provisionally install the engine assembly with transaxle and front suspension crossmember onto the vehicle with the 6 bolts.

  1. Insert SST into the datum holes for the front suspension crossmembers RH and LH alternately and tighten bolts A, B and C on both sides in several steps.

    SST
    09670-00010  

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf } bolt A
    160 N*m{ 1631 kgf*cm , 118 ft.*lbf } bolt B
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } bolt C

    NOTICE:
    1. Insert SST into the datum hole vertically.
    2. If impossible to insert SST vertically, loosen all the bolts and then insert SST again.


    A117079E01


39. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the inboard joint with gear oil.

  1. C116899
    Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.


40. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


41. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


42. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


43. INSTALL FRONT NO. 2 SUSPENSION ARM SUB-ASSEMBLY LOWER LH

C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


44. INSTALL FRONT NO. 2 SUSPENSION ARM SUB-ASSEMBLY LOWER RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


45. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


46. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


47. INSTALL TIE ROD END SUB-ASSEMBLY LH

C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


48. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


49. INSTALL FRONT SPEED SENSOR LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


50. INSTALL FRONT SPEED SENSOR RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


51. INSTALL FRONT AXLE SHAFT LH NUT

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


52. INSTALL FRONT AXLE HUB RH NUT

HINT:
The installation procedure for the RH side is the same as that for the LH side.


53. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. A104634
    Using vernier calipers, measure the free length of the compression spring.

    Minimum length:
    40.5 mm (1.594 in.)

    If the length is not as specified, replace the compression spring.

  1. A104635
    Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports.

  1. Install the exhaust pipe assembly front and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


54. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

A127617E01
  1. Install clip B onto the body portion and install the column hole cover onto the body portion with clip A.

    NOTICE:
    Make sure that the lip portion of the column hole cover is not damaged.


55. CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

A127616E01
  1. Align the matchmarks and install the sliding yoke and the intermediate shaft with bolt B.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


56. INSTALL COLUMN HOLE COVER SILENCER SHEET

A127614
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.


57. CONNECT ENGINE WIRE

A129219
  1. Move the lever down to engage the lock and connect the connector to the engine control computer.

  1. A127612
    Install the 3 clamps and the band and connect the connector of the No. 2 oxygen sensor.

  1. A127611
    Connect the connector and 2 clamps.

  1. A127610
    Connect the 2 connectors shown in the illustration.

  1. A127609
    Connect the bolt and wire harness clamp.

    Torque:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }


58. CONNECT CONNECTOR (for Multi-Mode Manual Transaxle)
  1. Connect all connectors and clamps for the multi-mode manual transaxle.


59. CONNECT FLOOR SHIFT CABLE TRANSMISSION CONTROL SELECT (for Manual Transaxle)

A127608
  1. Connect the floor shift cable transmission control select with the 2 pins and the 2 clips.


60. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

A127607E01
  1. Install the clutch release cylinder and clutch pipe with the 4 bolts.

    Torque:
    14 N*m{ 142 kgf*cm , 10 ft.*lbf } bolt A
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } bolt B

  1. A127606
    Install the clutch release cylinder cover with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


61. CONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

A129215
  1. Connect the union to the connector tube hose.


62. CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

A129214
  1. Connect the union to the connector tube hose.


63. CONNECT HEATER WATER OUTLET HOSE A

A127605
  1. Connect the water by-pass hose.

  1. A129160
    Connect the heater water outlet hose.


64. CONNECT HEATER WATER INLET HOSE A

A127604
  1. Connect the water by-pass hose.

  1. A129159
    Connect heater water inlet hose A.


65. CONNECT FUEL HOSE SUB-ASSEMBLY

A127655
  1. Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound.

    NOTICE:
    1. Check that there are no scratches or foreign matter on the fuel tube connector and pipe joint.
    2. After connecting the fuel tube, pull the pipe and fuel tube connector to make sure that they are securely connected.

  1. A127194
    Install the fuel pipe clamp.


66. CONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A127212
    Connect the No. 1 fuel vapor feed hose.


67. CONNECT NO. 2 RADIATOR HOSE

A127603
  1. Connect the No. 2 radiator hose with the clamp.


68. CONNECT NO. 1 RADIATOR HOSE

A127602
  1. Connect the No.1 radiator hose with the clamp.


69. INSTALL WITH PULLEY COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

A108955
  1. Provisionally tighten the compressor with the bolt.

  1. Tighten the compressor with the 3 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connector.


70. ADJUST FAN AND GENERATOR V BELT

A127651E01
  1. Turn adjusting bolt C and adjust the tension of the V-belt.

  1. Tighten fixing bolts A and B.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf } bolt A
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } bolt B


71. INSPECT FAN AND GENERATOR V BELT

A127654E01
  1. Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    7.0 to 8.0 mm (0.28 to 0.31 in) w/ air conditioning system
    4.0 to 5.0 mm (0.16 to 0.20 in) w/o air conditioning system
    Used belt
    9.0 to 9.5 mm (0.35 to 0.37 in) w/ air conditioning system
    6.0 to 6.5 mm (0.24 to 0.26 in) w/o air conditioning system

    Tension:
    Item
    Specified Condition
    New belt
    687 to 883 N (70 to 90 kg, 154 to 199 ld) w/ air conditioning system
    785 to 981 N (80 to 100 kg, 176 to 221 ld) w/o air conditioning system
    Used belt
    539 to 637 N (55 to 65 kg, 121 to 143 ld)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Check the V belt deflection at the specified point.
    2. When installing a new belt, set its tension to the specified value.
    3. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    4. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    5. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    6. When using a belt tension gauge, confirm its accuracy by using a master gauge first.


72. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

73. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

A127601
  1. Engage the air cleaner cap, install the air inlet onto the reservoir tank and install the air cleaner cap.


74. INSTALL BATTERY CARRIER

A108954
  1. Install the battery carrier with 5 bolts.

  1. Connect the 4 wire harness clamps.

    Torque:
    17 N*m{ 174 kgf*cm , 13 ft.*lbf }


75. INSTALL BATTERY TRAY

76. INSTALL BATTERY

  1. A104324
    Install the battery onto the battery tray.

  1. Install the battery carrier clamp with the nut.

  1. Install the positive and negative terminals.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


77. INSTALL COWL TOP PANEL OUTER

  1. A131385
    Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A131386
    Engage the clamp and install the wiper motor connector wire harness.


78. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

  1. A118801E01
    Engage the 2 claws and install cowl to register duct No. 2.


79. INSTALL WINDSHIELD WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


80. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


81. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


82. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


83. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


84. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


85. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


86. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


87. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


88. ADD MULTI-MODE MANUAL TRANSAXLE OIL (for Multi-Mode Manual Transaxle)

89. INSPECT MULTI-MODE MANUAL TRANSAXLE OIL (for Multi-Mode Manual Transaxle)

D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the filler plug opening.

    NOTICE:
    1. An excessively large or small amount of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. When the oil level is low, check for oil leakage.

  1. Install the filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


90. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

91. INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.

  1. D025304E03
    Check that the oil surface is within 5 mm (0.20 in.) of the bottom of the transmission filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause problems.
    1. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


92. ADD ENGINE COOLANT
  1. Tighten all the plugs.

  1. Disconnect the vinyl hose.

  1. Pour engine coolant into the radiator assembly until it overflows.

    Capacity:
    5.1 liters (5.4 USqts, 4.5 lmp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper engine coolant may damage the engine coolant system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.

  1. Install the radiator cap sub-assembly securely.

  1. Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Stop the engine and wait until the coolant cools down.

  1. If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.

  1. Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.


93. ADD ENGINE OIL

94. CHECK FOR ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A127379
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


95. CHECK FOR ENGINE OIL LEAKAGE

96. CHECK FOR EXHAUST GAS LEAK

97. INSPECT IGNITION TIMING

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A127178E01
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items:
      Powertrain / Engine and ECT / Active Test / TC (TE1) / ON.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    6. Select the following menu items: TC (TE1) / OFF

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester:

    1. Remove the air cleaner cap sub-assembly (Click here).

    2. A127234
      Pull out the wire harness shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    3. Warm up and stop the engine.

    4. Connect the clip of the timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. Turn the ignition switch on (IG).

    6. A082779E23
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the ignition timing with the cooling fan off.
      3. When checking the ignition timing, shift the transmission to the neutral position.

    8. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    9. Turn the ignition switch off.

    10. Remove the timing light.

    11. Install the air cleaner cap sub-assembly (Click here).


98. INSPECT ENGINE IDLING SPEED

  1. When using an intelligent tester:

    1. Warm up and stop the engine.

    2. A127178E01
      Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch on (IG).

    4. Select the following menu items: Powertrain / Engine and ECT /Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    5. Inspect the engine idling speed.

      Idling speed:
      550 to 650 rpm (for Manual Transaxle)
      550 to 650 rpm (for Multi-Mode Manual Transaxle)

      NOTICE:
      1. Turn all the electrical systems and the A/C off.
      2. Inspect the idling speed with the cooling fan off.
      3. When checking the idling speed, shift the transmission to either the neutral position or the parking position.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DLC3.

  1. When not using an intelligent tester.

    1. Warm up and stop the engine.

    2. A082779E24
      Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
      SST
      09843-18040  

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    3. Turn the ignition switch on (IG).

    4. Inspect the engine idling speed.

      Idling speed:
      600 to 700rpm

    5. Turn the ignition switch off.

    6. Disconnect the tachometer.

    7. Remove SST from terminal 9 (TAC).


99. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.

  1. Check the CO/HC concentration during idling and when running at 2,500 rpm.

    HINT:
    When doing the 2 mode (with the engine idling/running at 2,500 rpm) test, the measuring procedures are determined by applicable local regulations.

    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problems
      Possible Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Dirty, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leakage from intake and exhaust valves
      4. Leakage from cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body


100. INSTALL ENGINE UNDER COVER RH

101. INSTALL ENGINE UNDER COVER LH

102. INSTALL FRONT TIRE

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


103. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

104. INSPECT ABS SENSOR SIGNAL
(Click here)

105. REMOVE CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)

106. CHECK FUEL PUMP OPERATION AND FUEL LEAKAGE

  1. A127178E01
    When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.

← REMOVAL (from Nov 2005)COMPONENTS (from Nov 2005) →