INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL RADIATOR DRAIN COCK |
Install the radiator drain cock onto the radiator assembly.

| 2. INSTALL RADIATOR RESERVE TANK HOSE GROMMET |
Install the 2 radiator reserve tank hose grommets onto the radiator assembly.

| 3. INSTALL RADIATOR SUPPORT CUSHION |
Install the 2 radiator support cushions onto the radiator assembly.

| 4. INSTALL FAN SHROUD NO. 2 |
Engage the 2 claws and install fan shroud No. 2.

| 5. INSTALL RADIATOR HOSE NO. 3 |
Install radiator hose No. 3 with the clip.

| 6. INSTALL WATER FILLER SUB-ASSEMBLY |
Install the water filler sub-assembly with the clip.

Install the 2 bolts.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
Connect the radiator reserve tank hose.
| 7. INSTALL RADIATOR ASSEMBLY (w/ Air Conditioning System) |
Engage the 2 claws and install the radiator assembly onto the vehicle.

- NOTICE:
- Do not apply excessive force to the cooler condenser assembly or piping when installing the radiator assembly.
Connect the cooling fan motor connector and wire harness clamp.

Engage the 3 clamps for the oxygen sensor wire harness.
| 8. INSTALL RADIATOR ASSEMBLY (w/o Air Conditioning System) |
Install the radiator assembly onto the vehicle.

Connect the cooling fan motor connector and wire harness clamp.
Engage the 3 clamps for the oxygen sensor wire harness.
| 9. CONNECT RADIATOR HOSE NO. 2 |
Connect radiator hose No. 2 with the clip.

| 10. CONNECT RADIATOR HOSE NO. 1 |
Connect radiator hose No. 1 with the clip.

| 11. INSTALL AIR CLEANER INLET NO. 1 |
Install air cleaner inlet No. 1 onto the radiator reserve tank.

| 12. INSTALL RADIATOR SUPPORT UPPER |
Install the radiator support upper with the 4 bolts.

- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
Connect the horn assembly connector.
| 13. INSTALL HOOD LOCK ASSEMBLY |
Temporarily install the hood lock assembly with the 3 bolts.

Install the hood lock control cable assembly with the 2 clamps.

| 14. INSTALL COOLER COVER NO. 1 (w/ Air Conditioning System) |
Insert the 2 pins of cooler cover No. 1 into the radiator support LWR.

Install cooler cover No. 1 with the 2 clips.
| 15. INSTALL RADIATOR SUPPORT ABSPRBER UPPER |
Engage the 6 claws and install the radiator support absprber upper.

| 16. INSTALL FRONT BUMPER COVER |
w/ Front Spoiler:

Install the 2 clips and the 4 screw grommets.
w/o Front Spoiler:

Install the 2 clips and the screw grommet.
w/ Fog Light:
Connect the 2 fog light connectors.

Engage the 6 claws and install the front bumper cover.
w/o Fog Light:

Engage the 6 claws and install the front bumper cover.
w/ Front Spoiler:

Install the 7 clips.
Install the 2 screw grommets.
Tighten the 3 screws.
w/o Front Spoiler:

Install the 7 clips.
Install the 2 screw grommets.
Tighten the 8 screws.
Remove the protective tape.

| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 18. ADD ENGINE COOLANT |
Tighten all the plugs.
Disconnect the vinyl hose.
Pour engine coolant into the radiator assembly until it overflows.
- Capacity:
- 5.1 liters (5.4 USqts, 4.5 lmp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- Use of improper engine coolant may damage the engine coolant system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper engine coolant may damage the engine coolant system.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Manual air conditioning system
Automatic air conditioning system
Set control as follows
Fan speed - Any setting except "OFF"
Temperature - Toward WARM
Air conditioning switch "OFF"
Fan speed - Any setting except "OFF"
Temperature - To the highest temperature
Air conditioning switch "OFF"
"AUTO" switch "OFF"
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.
| 19. ADJUST HOOD LOCK ASSEMBLY |
Loosen the 3 bolts.

Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
- Torque:
- 7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
| 20. CHECK FOR ENGINE COOLANT LEAK |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

Pump the tester to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
