REMOVAL
Removal / installation · Vehicles built from Nov 2005
- CAUTION:
- Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN ENGINE COOLANT |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Install a vinyl hose onto the radiator.

Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.
Loosen the water drain plug, then drain the coolant.


| 3. REMOVE FRONT BUMPER COVER |
Apply protective tape as shown in the illustration.

w/ Front Spoiler:

Remove the 3 screws.
Remove the 2 screw grommets.
Remove the 7 clips.
w/o Front Spoiler:

Remove the 8 screws.
Remove the 2 screw grommets.
Remove the 7 clips.
w/ Fog Light:

Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.
Disconnect the 2 fog light connectors.
w/o Fog Light:

Using a screwdriver with its tip wrapped in protective tape, disengage the 6 claws and remove the front bumper cover.
w/ Front Spoiler:

Remove the 2 clips and the 4 screw grommets.
w/o Front Spoiler:

Remove the 2 clips and the screw grommet.
| 4. REMOVE RADIATOR SUPPORT ABSPRBER UPPER |
Disengage the 6 claws and remove the radiator support absprber upper.

| 5. REMOVE COOLER COVER NO. 1 (w/ Air Conditioning System) |
Remove the 2 clips and cooler cover No. 1.

| 6. REMOVE HOOD LOCK ASSEMBLY |
Separate the hood lock control cable assembly from the 2 clamps.

Remove the 3 bolts and remove the hood lock assembly.

| 7. REMOVE RADIATOR SUPPORT UPPER |
Separate the horn assembly connector.

Remove the 4 bolts and remove the radiator support upper.
| 8. SEPARATE AIR CLEANER INLET NO. 1 |
Separate air cleaner inlet No. 1 from the radiator reserve tank.

| 9. DISCONNECT RADIATOR HOSE NO. 1 |
Loosen the clip and disconnect radiator hose No. 1.

| 10. DISCONNECT RADIATOR HOSE NO. 2 |
Loosen the clip and disconnect radiator hose No. 2.

| 11. REMOVE RADIATOR ASSEMBLY (w/ Air Conditioning System) |
Separate the cooling fan motor connector and wire harness clamp.

Disengage the 3 clamps for the oxygen sensor wire harness.
Disengage the 2 claws and remove the radiator assembly from the vehicle.

- NOTICE:
- Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.
| 12. REMOVE RADIATOR ASSEMBLY (w/o Air Conditioning System) |
Separate the cooling fan motor connector and wire harness clamp.

Disengage the 3 clamps for the oxygen sensor wire harness.
Remove the radiator assembly from the vehicle.
| 13. REMOVE WATER FILLER SUB-ASSEMBLY |
Separate the radiator reserve tank hose.

Remove the 2 bolts and separate the water filler sub-assembly.
Loosen the clip and remove the water filler sub-assembly.
| 14. REMOVE RADIATOR HOSE NO. 3 |
Loosen the clip and remove radiator hose No. 3.

| 15. REMOVE FAN SHROUD NO. 2 |
Disengage the 2 claws and remove fan shroud No. 2.

| 16. REMOVE RADIATOR SUPPORT CUSHION |
Disengage the 2 radiator support cushions from the radiator assembly.

| 17. REMOVE RADIATOR RESERVE TANK HOSE GROMMET |
Remove the 2 radiator reserve tank hose grommets from the radiator assembly.

| 18. REMOVE RADIATOR DRAIN COCK |
Remove the radiator drain cock from the radiator assembly.

