2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL GENERATOR ASSEMBLY

  1. A128275E01
    Provisionally install generator with fixing bolt C.

  1. Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf } for Bolt B

  1. A128274
    Install the connector and wire harness clamp.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


2. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the V belt onto the pulleys.


3. INSTALL WIRE HARNESS CLAMP BRACKET (for LHD)

  1. A128273E01
    Install the 2 wire harness clamp brackets with the 2 bolts.

  1. Install the 2 harness clamps.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf } for Bolt A
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf } for Bolt B


4. INSTALL CAM TIMING OIL CONTROL VALVE ASSEMBLY

  1. A128272
    Install the cam timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the cam timing oil control valve assembly connector.


5. ADJUST FAN AND GENERATOR V BELT

A127651E01
  1. Turn adjusting bolt C and adjust the tension of the V-belt.

  1. Tighten fixing bolts A and B.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf } bolt A
    44 N*m{ 449 kgf*cm , 33 ft.*lbf } bolt B


6. INSPECT FAN AND GENERATOR V BELT

A127654E01
  1. Check the V belt deflection and tension.

    Deflection:
    Item
    Specified Condition
    New belt
    7.0 to 8.0 mm (0.28 to 0.31 in) w/ air conditioning system
    4.0 to 5.0 mm (0.16 to 0.20 in) w/o air conditioning system
    Used belt
    9.0 to 9.5 mm (0.35 to 0.37 in) w/ air conditioning system
    6.0 to 6.5 mm (0.24 to 0.26 in) w/o air conditioning system

    Tension:
    Item
    Specified Condition
    New belt
    687 to 883 N (70 to 90 kg, 154 to 199 ld) w/ air conditioning system
    785 to 981 N (80 to 100 kg, 176 to 221 ld) w/o air conditioning system
    Used belt
    539 to 637 N (55 to 65 kg, 121 to 143 ld)

    If the belt deflection is not as specified, adjust it.

    HINT:
    1. Check the V belt deflection at the specified point.
    2. When installing a new belt, set its tension to the specified value.
    3. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    4. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    5. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    6. When using a belt tension gauge, confirm its accuracy by using a master gauge first.


7. INSTALL ENGINE UNDER COVER RH

Torque:
5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← REASSEMBLY (from Nov 2005)PRECAUTION (from Nov 2006) →