2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE ENGINE UNDER COVER RH

4. REMOVE ENGINE UNDER COVER LH

5. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 4 bolts and 4 compression springs.

  1. Remove the 3 exhaust pipe support, No. 4 and the exhaust pipe assembly front.


6. DRAIN ENGINE OIL
  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


7. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A117319
    Install a vinyl hose onto the radiator.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the water drain plug, then drain the coolant.

    A128298E01


8. REMOVE FRONT WHEEL

9. REMOVE HOOD SUB-ASSEMBLY

10. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


12. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


13. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


15. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


16. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


17. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


18. REMOVE WINDSHIELD WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


19. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

  1. A118801E01
    Disengage the claws and remove cowl to resister duct No. 2.


20. REMOVE COWL TOP PANEL OUTER

  1. A131386
    Disengage the clamp and separate the wiper motor connector.

  1. A131385
    Remove the 9 bolts and the cowl top panel outer.


21. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A127144
    Remove the grommet and 2 clamps and remove the air cleaner cap sub-assembly.


22. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

23. REMOVE PURGE VSV ASSEMBLY

  1. A127147
    Remove the bolt and remove the purge VSV assembly.


24. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A127148
    Disconnect the mass air flow meter connector.

  1. A127149
    Remove the 3 bolts and remove the air cleaner case sub-assembly.

  1. A127151
    Remove the O-ring from the throttle body assembly.


25. DISCONNECT NO. 1 WATER BY-PASS HOSE

  1. A127150
    Disconnect the 2 No. 1 water by-pass hoses.


26. DISCONNECT NO. 2 VENTILATION HOSE

  1. A127152
    Disconnect the No. 2 ventilation hose from the throttle body assembly.


27. DISCONNECT CHARCOAL CANISTER FUEL HOSE

  1. A127153
    Disconnect the charcoal canister fuel hose from throttle body assembly.


28. REMOVE THROTTLE BODY ASSEMBLY

  1. A127154
    Disconnect the connector from the throttle body assembly.

  1. A127155
    Remove the 3 bolts and remove the throttle body assembly.

  1. A127156
    Remove the O-ring from the intake manifold.


29. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

  1. A127161
    Disconnect the union to connector tube hose from the intake manifold.


30. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

  1. A127162
    Disconnect the union to connector tube hose from the intake manifold.


31. DISCONNECT VENTILATION HOSE (for LHD)

  1. A127163
    Disconnect the ventilation hose from the cylinder head.


32. DISCONNECT VENTILATION HOSE (for RHD)

  1. A127164
    Disconnect the ventilation hose from the cylinder head.


33. DISCONNECT ENGINE WIRE (for LHD)

  1. A127165
    Disengage the 2 engine wire harness clamps.

  1. A131384
    Remove the bolt and remove the harness bracket.


34. DISCONNECT ENGINE WIRE (for RHD)

  1. A127166
    A131384
    Disengage the 2 engine wire harness clamps.
    Remove the bolt and remove the harness bracket.


35. REMOVE THROTTLE BODY BRACKET

  1. A127168
    Remove the 2 bolts and remove the throttle body bracket.


36. REMOVE INTAKE MANIFOLD

  1. A127169
    Remove the 3 bolts and 2 nuts and remove the intake manifold.

  1. Remove the intake manifold gasket.


37. REMOVE WIRING HARNESS CLAMP BRACKET

A129154
  1. Disconnect the oxygen sensor connector.

  1. A129155
    Remove the bolt and remove the wiring harness clamp bracket.


38. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

A129156
  1. Remove the 3 bolts and remove the exhaust manifold heat insulator.


39. REMOVE MANIFOLD STAY

A127627
  1. Remove the bolt and nut and remove the manifold stay.


40. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A135336
    Remove the bolt and wire harness clamp.

  1. A127628E02
    Remove the 2 nuts and 3 bolts and remove the manifold converter.

  1. Remove the exhaust manifold gasket.


41. DISCONNECT NO. 1 RADIATOR HOSE

A129157
  1. Disconnect the No. 1 radiator hose.


42. DISCONNECT NO. 2 RADIATOR HOSE

A129158
  1. Disconnect the No. 2 radiator hose.


43. DISCONNECT HEATER WATER INLET HOSE A

A129159
  1. Disconnect heater water inlet hose A.


44. DISCONNECT HEATER WATER OUTLET HOSE A

A129160
  1. Disconnect heater water outlet hose A.


45. REMOVE FUEL HOSE SUB-ASSEMBLY

A127194
  1. Remove the fuel delivery pipe clamp.

  1. A127202E01
    Pinch the fuel tube connector retainer from both sides, disconnect the fuel tube connector and separate the fuel tube from the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting, as the fuel tube connector has the O-rings that seal the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected parts by covering them with vinyl bags after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.


46. REMOVE IGNITION COIL ASSEMBLY

  1. A127191
    Disconnect the 4 ignition coil assembly connectors.

  1. A127192
    Remove the 4 bolts and 4 ignition coils.


47. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY

48. DISCONNECT ENGINE WIRE (for LHD)

A127660
  1. Disengage the 2 engine wire harness clamps.

  1. A127661
    Remove the 2 bolts and disconnect the engine wire harness.


49. DISCONNECT ENGINE WIRE (for RHD)

A127659
  1. Disengage the engine wire harness clamp.

  1. A127661
    Remove the 2 bolts and disconnect the engine wire harness.


50. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A127662
  1. Remove the 11 bolts, 2 nuts and 2 seal washers and remove the cylinder head cover.


51. DISCONNECT FAN AND GENERATOR V BELT

A127651E01
  1. Loosen bolts A and B.

  1. Turn adjusting bolt C to release the tension and remove the V belt from the pulleys.


52. REMOVE CRANKSHAFT PULLEY

  1. A129213E01
    w/o service hole:

    1. Using SST, hold the crankshaft pulley and loosen the bolt.

      SST
      09960-10010   (09963-01000, 91651-60855)

  1. A131374E01
    w/ service hole:

    1. Using SST, hold the crankshaft pulley and loosen the bolt.

      SST
      09330-00021  
      09213-54015   (91651-60855)

  1. A131396
    Remove the bolt and remove the crankshaft pulley.


53. REMOVE WATER PUMP PULLEY

A129122E01
  1. Using SST, hold the water pump pulley and remove the 4 bolts.

    SST
    09960-10010   (09963-00500)


54. REMOVE IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127696
  1. Remove the nut and washer and remove the idler pulley.


55. REMOVE CRANKSHAFT POSITION SENSOR

  1. A127186
    Disconnect the crankshaft position sensor connector.

  1. Remove the bolt and remove the crankshaft position sensor.


56. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY (w/ Air Conditioning System)

A127697
  1. Remove the bolt, nut and washer and remove the No. 2 idler pulley.


57. REMOVE CAM TIMING OIL CONTROL VALVE ASSEMBLY

  1. A127180
    Disconnect the connector.

  1. Remove the bolt and remove the cam timing oil control valve assembly.


58. REMOVE OIL PAN SUB-ASSEMBLY

A127698
  1. Remove the service hole cover.

  1. A129121
    Remove the 2 nuts and 16 bolts.

  1. A129127
    Using a screwdriver with its tip wrapped in protective tape, pry out the oil pan.

    NOTICE:
    Do not damage the oil pan or the cylinder block.


59. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

A127622
  1. Install the bolt and install engine hanger.

  1. Using a chain block, hang up the engine.

  1. A127653
    Remove the bolt and remove the low pressure pipe bracket of the air conditioner (w/air conditioning).

  1. A129120
    Remove the 5 bolts and nut and remove the engine mounting insulator.


60. REMOVE FAN AND GENERATOR V BELT
  1. Remove the fan and generator V belt.


61. REMOVE ENGINE MOUNTING STAY RH

A129123
  1. Remove the 2 bolts and remove engine mounting stay RH.


62. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A129124
  1. Remove the 2 bolts and nut and remove the engine mounting bracket.


63. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

A129208
  1. Remove the 10 bolts and 2 stud bolts.

  1. A129125
    Using a screwdriver with its tip wrapped in protective tape, pry out the timing chain cover.

    NOTICE:
    Do not damage the timing chain cover, the cylinder block or the cylinder head.

  1. A129126
    Remove the gasket.


64. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

A129128
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil seal.


65. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

A083159
  1. Remove the No. 1 crankshaft position sensor plate.


66. REMOVE CHAIN TENSIONER PLUNGER

A129129E01
  1. Move the stopper plate downward and hold it with its lock released.

    HINT:
    If the lock of the stopper plate is hard to release, using the hexagonal portion of the camshaft, turn the camshaft slightly left and right.

  1. A129130
    Keep the stopper plate with the plunger pushed to the end of the stopper plate.

  1. A129131E01
    Align the holes in the stopper plate and the chain tensioner plunger.

    HINT:
    If it is hard to align the holes in the stopper plate and the chain tensioner plunger, slightly turn the camshaft both ways and align them.

  1. A129133
    Insert a 3mm diameter bar into the holes in the stopper plate and the chain tensioner plunger.

  1. Remove the bolt and the nut and remove the chain tensioner plunger.


67. REMOVE TIMING CHAIN TENSION ARM

A129134
  1. Remove the bolt and remove the timing chain tension arm.


68. REMOVE TIMING CHAIN GUIDE

A129135
  1. Remove the 2 bolts and remove the timing chain guide.


69. REMOVE NO. 2 TIMING CHAIN GUIDE

A129136
  1. Remove the 2 bolts and remove the No. 2 timing chain guide.


70. REMOVE CHAIN SUB-ASSEMBLY

71. INSTALL OIL PAN SUB-ASSEMBLY
  1. Provisionally install the oil pan sub-assembly.

  1. Remove the chain block.

  1. Support the Oil pan with a jack.

    NOTICE:
    Be careful not to damage the oil pan while supporting it with the jack.


72. REMOVE CAMSHAFT TIMING SPROCKET ASSEMBLY

A129161
  1. Using the hexagonal portion of the camshaft hold the camshaft and remove the camshaft timing sprocket.


73. REMOVE NO. 2 CAMSHAFT

A129162
  1. Remove the 4 bolts and remove the bearing cap.

  1. A127677
    Using the hexagonal head portion of the camshaft, revolve the camshaft so that the cam noses of cylinders No. 2 and No. 4 face as shown in the illustration.

  1. A131389E01
    Remove the camshaft bearing caps and bolts in the sequence shown in the illlustration.

  1. A131391
    Remove the exhaust camshaft assembly and camshaft timing gear.


74. REMOVE CAMSHAFT

A127679
  1. Using the hexagonal head portion of the camshaft, revolve the camshaft so that the cam noses of cylinders No. 3 and No. 4 face as shown in the illustration.

  1. A127680E01
    Remove the camshaft bearing caps and bolts in the sequence shown in the illustration.

  1. A131392
    Remove the camshaft.


75. REMOVE CYLINDER HEAD SUB-ASSEMBLY

A129163E01
  1. Using several steps, loosen and remove the 10 cylinder head bolts uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration. Remove the 10 cylinder head bolts and the 10 plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing the bolts in the wrong order.


76. REMOVE CYLINDER HEAD GASKET

A129164
  1. Remove the cylinder head gasket.


77. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

A129165
  1. Remove the 2 bolts and remove the fuel delivery pipe together with the fuel injector assembly from the cylinder head.

  1. Remove the 4 insulators from the cylinder head.


78. REMOVE FUEL INJECTOR ASSEMBLY

  1. A127204
    Remove the 4 injectors from the delivery pipe sub-assembly.

  1. A107004E01
    Remove the O-ring and insulator from each injector.

  1. A127656
    Remove the 2 insulators from the delivery pipe sub-assembly.


79. REMOVE HARNESS BRACKET

A129166
  1. Remove the bolt and remove the harness bracket.


80. REMOVE SPARK PLUG

A131355
  1. Remove the 4 spark plugs.


81. REMOVE RADIO SETTING CONDENSER

A129167
  1. Remove the bolt and remove the radio setting condenser.


82. REMOVE CAMSHAFT POSITION SENSOR

A129168
  1. Remove the bolt and remove the camshaft position sensor.


83. REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR

A129169
  1. Using a deep socket 19 mm, remove the engine coolant temperature sensor.


84. REMOVE WATER INLET

A129170
  1. Remove the bolt and nut and remove the water inlet.


85. REMOVE THERMOSTAT

A129171
  1. Remove the thermostat from cylinder head.

← COMPONENTS (from Nov 2005)DISASSEMBLY (from Nov 2005) →