2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Transmission Control ECU and ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Aug 2005 – Oct 2005

Versions by build date: Aug 2005 – Oct 2005 from Nov 2005

DESCRIPTION

DTC No.
DTC Detection Conditions
Trouble Area
Transmission Control ECU and ECM Communication Stop Mode
  1. "ECT" or not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "Transmission Control ECU and ECM Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of transmission control ECU or ECM
  2. Transmission control ECU or ECM main wire or connector
  3. Transmission control ECU
  4. ECM

HINT:
For vehicle with multi-mode manual transaxle only.


WIRING DIAGRAM

C132295E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS WIRE

  1. C132290E01
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    A38-1 (CAN+) - A38-2 (CAN-)
    Ignition switch off
    54 to 69 Ω
    A
    A38-1 (CAN+) - A38-2 (CAN-)
    Ignition switch off
    69 Ω or higher
    B
    A38-1 (CAN+) - A38-2 (CAN-)
    Ignition switch off
    54 Ω less
    C



B
Go to step 11

C
Go to step 13
A


2. CHECK CAN BUS LINE FOR SHORT TO +B

  1. C132290E02
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - D79-1 (+B)
    Ignition switch off
    1 MΩ or higher
    A38-1 (CAN+) - D79-1 (+B)
    Ignition switch off
    1 MΩ or higher



NG
Go to step 7
OK


3. CHECK CAN BUS LINE FOR SHORT TO GND

  1. C132290E03
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - D79-6 (GND)
    Ignition switch off
    1 kΩ or higher
    A38-1 (CAN+) - D79-6 (GND)
    Ignition switch off
    1 kΩ or higher



NG
Go to step 9
OK


4. CHECK HARNESS AND CONNECTOR (+B, IG, GND)

  1. C132291E01
    Turn the ignition switch off.

  1. Disconnect the D79 transmission control ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A79-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D79-1 (+B) - Body ground
    Always
    10 to 14V
    D79-3 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14V



OK
REPLACE TRANSMISSION CONTROL ECU
NG


5. CONNECT CONNECTOR
  1. Reconnect the transmission control ECU connector.


NEXT


6. INSPECT ECM POWER SOURCE CIRCUIT
  1. 1KR-FE engine:

    1. Inspect the power source circuit (Click here)



OK
REPLACE ECM
NG

GO TO ECM POWER SOURCE CIRCUIT

7. CHECK CAN BUS LINE FOR SHORT TO +B (TRANSMISSION CONTROL ECU)

  1. C130932E02
    Turn the ignition switch off.

  1. Disconnect the A38 and D79 transmission control ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - D79-1 (+B)
    Ignition switch off
    1 MΩ or higher
    A38-2 (CAN-) - D79-1 (+B)
    Ignition switch off
    1 MΩ or higher



OK
REPLACE TRANSMISSION CONTROL ECU
NG


8. CHECK CAN BUS LINE FOR SHORT TO +B (TRANSMISSION CONTROL ECU - ECM)

  1. C118186E05
    1KR-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A32 ECM connector.

    3. C130932E02
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79 transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher

  1. C125895E08
    2SZ-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A21 ECM connector.

    3. C130932E02
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79 transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher

  1. C130899E05
    1ND-TV engine:
    1. Turn the ignition switch off.

    2. Disconnect the A49 ECM connector.

    3. C130932E02
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79 transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-1 (+B)
      Ignition switch off
      1 MΩ or higher



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU - ECM (CAN-H, CAN-L))

9. CHECK CAN BUS LINE FOR SHORT TO GND (TRANSMISSION CONTROL ECU)

  1. C130932E03
    Turn the ignition switch off.

  1. Disconnect the A38 and D79 transmission control ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - D79-6 (GND)
    Ignition switch off
    1 MΩ or higher
    A38-2 (CAN-) - D79-6 (GND)
    Ignition switch off
    1 MΩ or higher



OK
REPLACE TRANSMISSION CONTROL ECU
NG


10. CHECK CAN BUS LINE FOR SHORT TO GND (TRANSMISSION CONTROL ECU - ECM)

  1. C118186E05
    1KR-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A32 ECM connector.

    3. C130932E03
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher

  1. C125895E08
    2SZ-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A21 ECM connector.

    3. C130932E03
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79 transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher

  1. C130899E05
    1ND-TV engine:
    1. Turn the ignition switch off.

    2. Disconnect the A49 ECM connector.

    3. C130932E03
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 and D79 transmission control ECU connectors are disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher
      A38-2 (CAN-) - D79-6 (GND)
      Ignition switch off
      1 MΩ or higher



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU - ECM (CAN-H, CAN-L))

11. CHECK CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU)

  1. C132289E01
    Turn the ignition switch off.

  1. Disconnect the A38 transmission control ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - A38-2 (CAN-)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE TRANSMISSION CONTROL ECU
NG


12. CHECK CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU - ECM)

  1. C132292E01
    1KR-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A32 ECM connector.

    3. Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A32-26 (CAN+) - A38-1 (CAN+)
      Always
      Below 1 Ω
      A32-34 (CAN-) - A38-2 (CAN-)
      Always
      Below 1 Ω

  1. C132293E01
    2SZ-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A21 ECM connector.

    3. Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A21-5 (CAN+) - A38-1 (CAN+)
      Always
      Below 1 Ω
      A21-4 (CAN-) - A38-2 (CAN-)
      Always
      Below 1 Ω

  1. C132294E01
    1ND-TV engine:
    1. Turn the ignition switch off.

    2. Disconnect the A49 ECM connector.

    3. Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A49-45 (CAN+) - A38-1 (CAN+)
      Always
      Below 1 Ω
      A49-64 (CAN-) - A38-2 (CAN-)
      Always
      Below 1 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU - ECM (CAN-H, CAN-L))

13. CHECK CAN BUS LINES FOR SHORT CIRCUIT (TRANSMISSION CONTROL ECU)

  1. C132289E01
    Turn the ignition switch off.

  1. Disconnect the A38 transmission control ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-1 (CAN+) - A38-2 (CAN-)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE TRANSMISSION CONTROL ECU
NG


14. CHECK CAN BUS LINES FOR SHORT CIRCUIT (TRANSMISSION CONTROL ECU - ECM)

  1. C118186E05
    1KR-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A32 ECM connector.

    3. C132289E01
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - A38-2 (CAN-)
      Ignition switch off
      1 MΩ or higher

  1. C125895E08
    2SZ-FE engine:
    1. Turn the ignition switch off.

    2. Disconnect the A21 ECM connector.

    3. C132289E01
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - A38-2 (CAN-)
      Ignition switch off
      1 MΩ or higher

  1. C130899E05
    1ND-TV engine:
    1. Turn the ignition switch off.

    2. Disconnect the A49 ECM connector.

    3. C132289E01
      Measure the resistance.

      HINT:
      The resistance must be measured after the A38 transmission control ECU connector is disconnected.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A38-1 (CAN+) - A38-2 (CAN-)
      Ignition switch off
      1 MΩ or higher



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (TRANSMISSION CONTROL ECU - ECM (CAN-H, CAN-L))


← ECM Communication Stop Mode (from Nov 2005)Transmission Control ECU and ECM Communication Stop Mode (from Nov 2005) →